Jump to content
SAU Community

Recommended Posts

May sound like a silly question,

I'll be towing my car on a car trailer for the first time next week and need some advice on how to tie the car down, eg. where do i tie down? the diff? each wheel? all 4 wheels? chains or truck tie down ok?

Link to comment
https://www.sau.com.au/forums/topic/386869-towing-a-car-on-a-trailer/
Share on other sites

where you tie it down sort of depends on the trailer and where the points are to tie it down. my opinion is to tie it down via parts of the car connected to the lower part of the suspension that aren't going to move too much if the suspension is compressed. for example, if you were to tie it down via the body somewhere, if you hit a big bump then the suspension of the car can compress and the chains/tie-downs can slacken and the car can move. but as i said, it comes down to where the points are on the trailer to tie down to.

also make sure that you have the car foward all the way so you have most of the weight over the front of the trailer. this will make it tow better. having too much weight over the back of the trailer is a good way to cause an accident once you pick up a bit of speed.

Thanks for the tips, im hoping that 4 ratchet tiedowns ( 1500kg rated each ) is enough around the lower suspension on each corner then, i think the tow trucks use chains and winches but ill be driving steady , its a 30min drive and the front of the trailer has a wire that hooks onto the tow hook, and the trailer has brakes . The trailer says its rated at 1200kg, do you guys see any problem if the skyline is 1400kg?

Do you guys think there is any issues with this setup? i know i could of just got a tow truck but it would be alot more expensive.

Think of the car as a tennis ball, doesn't matter which way you tilt the trailer (forward, backward, side) the tennis ball should not be able to move. Don't take any notice of how a tow truck operater secures a vehicle, 98% of them should be shot for their unsafe practices (a winch + 1 wheel tied down is not safe).

The easiest way is as Rekin has posted, using each wheel diagonally to the corner of the trailer. This prevents forward, backward and side movement but can play havoc on alignments.

Use 'hooker & keeper' 50mm ratchets which you can get a 4 pack from bunnings for about $50 rated to 1-2 ton. The amount of retards I see at motorsport events use 1x 20mm s-hook looped through the front axle and another looped through the back axle is astonishing. Most importantly is to tie it all down, then do a lap of the trailer to re-check each point then drive the car 50 or 100m and brake then get out and check it all again.

Just make sure your hand brake is on and the car is in the gear that you value the least. Chuck a mate in there to hold the brakes on and turn the wheel for a bit of extra friction for security.

Make sure it can't move by tying it on as said (I'd also have the winch tightened if you can) and then take it a bit easy, towing a trailer with a car on it isn't hard if you use your brain, let people overtake you and if the trailer gets unsettled don't smash your brakes, pump them once and power out.

Thanks guys for all the good advice,

Towed the car to ERD this morning, ended up using 3 tie downs and had my bro follow behind me in his car just to make sure it was ok, first time towing was a bit anxious lol, but was suprisingly smooth ride,

the car didnt move at all on the trailer and was solid, the EL falcon got a work out.. i can see why people use 4wd's to tow there drag cars.. the temp guage was sitting high and the brakes became shakey by the end.

Cheers :thumbsup:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • In a few years from now, you'll regret that. It'll eat away at you, knowing the truth of the ugly hiding beneath the beautiful exterior... 😛
    • I don't think the G2 profile is particularly dangerous for the engine per se, more just are you actually ok with the turbo lag trade-offs? If the answer is yes then go for it. I personally don't think I'd be ok with it because I spend so much time at lower RPMs and I really enjoy the feeling of being able to stay in 5th gear on the highway and just roll into the throttle to get boost. Or staying in 3rd gear on "gentle canyon cruises" without feeling the turbo lag too badly. The 525 pump should be able to run flat out on factory lines but I would bet the pressure drop from pump to regulator is quite impressive. I don't know how much it would be exactly but I've seen figures like 30 psi thrown around.
    • It's interesting seeing everyone talk about what level of risk they are happy to tolerate.  Building a GTR always has a level of risk, you could be that lucky guy that drops 20k on the engine build alone and still has the thing go pop on the dyno. Life is fun like that.  The way I see it, the thing is a toy to be enjoyed. I'd be happy to turn up the power on stock motor and limit the risk with sensible tuning and engine protection. If it still goes pop, it is what it is. The car isn't a daily driver so it can happily sit while a plan is made to sort it out.  Given this thing will be a street car only, I really feel it's worth the (relatively small if managed well) risk to turn the power up to around 350KW on e85.  I don't think anyone getting into the skyline game now is doing it out of logic. Surely it is a purely emotional decision so I'm not sure how important it is to think about the engine build logically. The heart wants what it wants.  @joshuaho96 little note for Josh, I run my 525 pump flat out all the time and through the factory lines without any issues. (excluding the melting connectors, that's sorted now. we'll pretend it never happened lol)
    • But the Nexus S3 is very expensive and won't be as purpose-built for the application as a separate electronic boost controller :^) More seriously my pet issue here would be that the Walbro 525 running at 100% duty cycle is going to require more FPR than the stock setup can handle. I'm also pretty sure from what I've seen elsewhere you might want to slow down the pump regardless unless you're going to come up with some way of upsizing the fuel lines coming from the fuel tank. Factory 8mm fuel line doesn't actually flow very much if you want to keep pressure drop down between the fuel pump outlet and FPR. If you really want to "keep it simple" I would run only as much pump as you need and source a fuel pump controller to slow down the pump in the vain hope of being able to run stock-style FPRs which are pretty dinky. Or just use the HICAS lines and it should be mostly fine. OP should also really think hard about what profile they'd want out of the turbo. My pet choice here would be the G1 profile rather than anything higher power but YMMV. I already think ~stock turbo lag is pretty bad so I don't want to make it worse. In "gentle canyon cruising" I found that I spent a lot of time around 4-4.5k RPM. I also recommend DIYing labor if you're detail-oriented enough. Costs are high for labor + if you do it yourself you can be your own quality control.
    • GTSBoy is again on the money. My actual advice? Sell the car. (really). For what it's worth as is, you can sidegrade into something much better. If you care about function then this is the actual move. If you want a Skyline to perform, set aside about $100K to do it. This is NOT a typo. You will see right away these are two very different mindsets. Realistically we're talking full restomod for any Skyline still kicking around. Have an honest think about which one you are.. and what you want to do, and how much you want to invest in this (with no return).
×
×
  • Create New...