Jump to content
SAU Community

Recommended Posts

Hi guys.

I started a separate thread on this, but I put it in the wrong section >_<

I've had a few of the Adelaide guys ask me about running a group buy on the AM Performance M35 exhausts, similar to what is on mine.

These exhaust components, dump pipes, mid pipes and cat back exhausts, are designed to bolt up to the factory mount points. So if you have one of Scotty's dump pipes, and a Nismo exhaust, you can just get the mid pipe if you want. Or you can get the whole lot, depending on what you need.

I need 5 people interested to go ahead. If you're interested, let me know.

For more info check out the original thread: http://www.skylinesaustralia.com/forums/topic/387032-eoi-am-performance-m35-exhaust-group-buy/

Any questions just let me know! :thumbsup:

PMs replied.

Little bit of interest, mainly in custom touches. I'm going to get proper photos of my twin muffler catback on the weekend, and I'm going to talk to Andrew about all of the custom requests.

If there are any more requests let me know.

  • 2 weeks later...

Whats the sound level like on theses?

Andrew, sound level is whatever you'd like. Twin mufflers will get you a nice deep note, and a lower sound level.

I'll try and use my mobile to check sound level, but I'm not sure how accurate those apps are?

I may be interested in the full system- off the turbo back- dump/front whatever its called right through to and twip tips, not titanium finish.

If you can price it up with postage to Sydney please. (insured?)

Thanks

Assuming you want twin mufflers, most people seem to be after quieter systems...

Dump pipe (catless) - $420 (usually $480)

Mid pipe with 200 cpsi ceramic cat - $400 (usually $450)

Cat back exhaust with twin mufflers - $870 (usually $930)

Total = $420 + 400 + 870 = $1690

Installation in SA is $280, postage is $75 Australia wide.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'd argue the F50 kit I got is very good value. For ~2k I got the calipers (refurbed condition), adapters, pads, brake lines, rotors, and top hats. I think you'd be pretty hard to get Evo/GTR/350z brembos + the additional hardware for similar money. Used market for a pair of front calipers alone I've seen tend to run anywhere from $1500-2000 depending on condition.    That said, something like a GTR or 350z brembo is a lot easier to adapt to the Silvia. 
    • Is there a significant price difference between the Evo/gtr/350z brembos vs the F50? Looks amazing.
    • I was actually being a tightarse at the time LOL... My OCD is tickling me into running a 2nd 8AN Teflon hose all the way down and removing the 2x OEM hardlines. My other side of my brain is telling me to run 2x hardlines front to back (also acts as a fuel cooler, so win win).
    • As I mentioned in an earlier post, I had some trouble with the Silvia's brakes dragging back in 2023. I managed to sort it out then, but the same problem came back to bite me late last year. Just take a look at the picture – I had a feeling the handbrake was acting up again, and I was right. Anyway, I'd been wanting to upgrade to bigger brakes for a while. Not that the Silvia's brakes were bad, but it was more of a "want" than a "need", you know? It was funny, though – at the time, I couldn't find any Evo Brembos, 350Z Brembos, or GTR Brembos for a decent price (of course, tons of them popped up online after I already bought my kit!). I ended up going with an F50 Brembo kit, which came with adapters, brake lines, 330mm rotors, and top hats. The F50 Brembo caliper was used in a few other cars too, like the FPV. I also decided this was the perfect opportunity to ditch the Silvia's ridiculous rear brakes and that awful handbrake (some of you were definitely right about that!). I picked up some R33 calipers and all the necessary bits – rear drums, backing plates, and new hardware to refurbish the calipers. Of course, it wouldn't be a project without a few hiccups. Turns out the brake master cylinder was playing up and basically (to put it simply) keeping the brakes engaged. I had it overhauled, and after some adjustments, everything was working again. The whole process took a while, as you can imagine. To top it off, the front right wheel bearings were shot and needed replacing too. This is a rare occasion where I'm posting an update while it's all still fresh! These pictures were taken just this afternoon.
    • I was just going to say that it's good to see you picking up the pace again. Hope the surgery goes well. More downtime just means more time to come up with new ways of digging a deeper rabbithole  
×
×
  • Create New...