Jump to content
SAU Community

Recommended Posts

Hi guys,

after much time spent in the garage, its past time to put this up for sale. I bought this in late 2011 to use a as a track project, but a lack of time has constricted its progress. It is being sold as a work in progress, so the buyer acknowledges it still has a little bit of work before completion. This car is TRACK ONLY, it was stolen in NSW and recovered by Police, sold at auction, and made its way to SA at some point, then i bought it. Please dont ask how hard it would be to get it on the street, i have no idea.

The list.

1994 Nissan Silvia Series 1

SR20DET manual

The outside:

some sort of bodykit, unknown. no front bar.

Brand new Rota Grid wheels (17 x 9.5 +12 all round)

Brand new 100% tread Federal 595SS all round (235/45/17)

Flared guards

The inside:

Typical gauge setup, Oil temp, water temp, oil pressure, boost gauge

A nameless fixed back bucket seat

OMP racing wheel with quick release hub and slim boss kit

AC and stereo removed

Monza Harness

Under the bonnet:

Kando Dynamic T518Z equivalent turbo (did research, great turbo!) (just needs oil drain plumbed to complete) (brand new)

Intercooler

850cc injectors (brand new)

LS1 truck coils, comes with plug clips, just need leads (not fitted) (brand new)

Clutch fan removed, thermo fitted with on/off missile switch in cabin

Bosch 040 in tank pump (not fitted) (brand new)

Ceramic Button clutch, brand new (not fitted)

Locked standard diff

Z32 afm (just need bigger intake pipe to fit) (brand new)

Oil cooler kit (brand new)

Alloy radiator (brand new)

HKS Hiper-D coilovers

R32 GTR non brembo front brakes with EBC red pads

HDI SBC D SE Boost controller (with antilag!)

Im sure i have missed things but ill update as i remember!

pics here: http://www.nissansilvia.com/forums/index.php?app=classifieds&module=core&do=view_item&item_id=1876

Whats left to be done to get it on the track:

Needs a ECU and tune (nistune would be a good way to go)

Plumb in oil drain

Fill with oil (provided)

Finish fitting boost controller

Drive.

Price: $8,900 neg.

Will consider trades for Nissan Stagea or Yamaha YZ125

Located in Pooraka, SA

PM me or SMS me on 0416 070 133.

Link to comment
https://www.sau.com.au/forums/topic/387109-s14-track-project/
Share on other sites

  • 2 weeks later...

Have had a few offers for other track projects, my preference is to sell the whole car for cash at this stage. Definitely not interested in swapping for another project.

  • 2 weeks later...
  • 1 month later...
  • 3 months later...

****

UPDATE - sold wheels, fmic, coilovers and exhaust. Take the car off my hands for $5000

****

after much time spent in the garage, its past time to put this up for sale. I bought this in late 2011 to use a as a track project, but a lack of time has constricted its progress. It is being sold as a work in progress, so the buyer acknowledges it still has a little bit of work before completion. This car is TRACK ONLY, it was stolen in NSW and recovered by Police, sold at auction, and made its way to SA at some point, then i bought it. Please dont ask how hard it would be to get it on the street, i have no idea.

The list.

1994 Nissan Silvia Series 1

SR20DET manual

The outside:

some sort of bodykit, unknown. no front bar.

Brand new Rota Grid wheels (17 x 9.5 +12 all round) -sold, will supply standard rims

Flared guards

The inside:

Typical gauge setup, Oil temp, water temp, oil pressure, boost gauge

A nameless fixed back bucket seat

OMP racing wheel with quick release hub and slim boss kit

AC and stereo removed

Monza Harness

Under the bonnet:

Kando Dynamic T518Z equivalent turbo

straight through exhaust - sold

Intercooler - sold

850cc injectors (brand new)

LS1 truck coils, comes with plug clips, just need leads (not fitted) (brand new)

Clutch fan removed, thermo fitted with on/off missile switch in cabin

Bosch 040 in tank pump (not fitted) (brand new)

Ceramic Button clutch, brand new (not fitted)

Locked standard diff

Z32 afm (just need bigger intake pipe to fit) (brand new)

Oil cooler kit (brand new)

Alloy radiator (brand new)

HKS Hiper-D coilovers - sold

R32 GTR non brembo front brakes with EBC red pads

HDI SBC D SE Boost controller (with antilag!)

Im sure i have missed things but ill update as i remember!

th_IMG00077-20101015-0921.jpg

th_IMG00078-20101015-0922.jpg

th_DSC_0177.jpg

261221_10150228092566666_697016665_7584705_8364421_n.jpg

photo before guard flaring

226193_10150254442461666_697016665_7842530_7669558_n.jpg

36141_439239181665_697016665_5678258_778208_n.jpg

no swaps, cash only

Not on here much, SMS me on 0416 070 133.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
×
×
  • Create New...