Jump to content
SAU Community

Recommended Posts

Hi everybody, have had our S2 C34 Stagea for about 3 weeks now and loving it, except for the Xanavi unit which hasnt functioned since we got the beauty ( was told it did use to work, which i doubt very much :angry: ) so am on the hunt for a replacement unit that does work. Have spoken to Nisswreck in SA (on the advise of Chris Rogers on this forum) and they are doubtful they have one, they are going to let me know tomorrow. If they dont, is there anyone out there who has one, and is willing to part with it. All ours does is show the "nissan " screen, does nothing else. Any help/ advise appreciated. Cheers.:thumbsup:post-89570-0-31998100-1325585992_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/387136-wtb-s2-c34-xanavi-unit/
Share on other sites

Hi everybody, have had our S2 C34 Stagea for about 3 weeks now and loving it, except for the Xanavi unit which hasnt functioned since we got the beauty ( was told it did use to work, which i doubt very much :angry: ) so am on the hunt for a replacement unit that does work. Have spoken to Nisswreck in SA (on the advise of Chris Rogers on this forum) and they are doubtful they have one, they are going to let me know tomorrow. If they dont, is there anyone out there who has one, and is willing to part with it. All ours does is show the "nissan " screen, does nothing else. Any help/ advise appreciated. Cheers.:thumbsup:post-89570-0-31998100-1325585992_thumb.jpg

same problem.. think its asking you to insert a cd.

Have you tried pressing the TV button to the left? As somebody else mentioned its on the CD function....

Try pressing the TV button then press the touch screen button to the top right. This will change the TV screen channel. If the cd is stuffed then you can use channel VT1 which is the front input (3.5mm jack I believe)

I have pushed and tried all button combinations. All the unit does is "beep" every minute or so. It wont play cds, and the climate control screen doesnt display unless you switch the car off and startit up again with the A/C on. Then it comes up on the screen, but you cant adjust anything because the touch screen doesnt work. Once the unit beeps, the A/C screen dissapears and it goes back to normal. Only buttons that work are the climate butons down the side of the unit.

I'm on my phone so sorry if this doesnt work... Scroll down to chooks post #26

http://www.skylinesaustralia.com/forums/topic/129786-air-con-filter/page__st__20

Might be of some use

You can entry service/diagnostic mode by holding down the 2 buttons......but its all in Japanese so you'll have to do some translating.

I have the service info showing the sub menus somewhere so I'll see if I can dig it up.

post-49793-0-51854500-1325806134_thumb.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Update Issues 5 (plus #4) - 10 After making a claim about issue #4's missing part, DeAgostini Japan sent a whole new issue #4 and it arrived about 2 weeks after that. That was back in early March. It took another 4 weeks to receive issues 5 - 13 though. This update is for issues 5 - 10. Ove the 5 issues the front left suspension and most of the engine have been completed. The quality of the castings and fit of the parts is quite good, it seems better than DeAgostini's BNR34 Skyline GT-R from the Fast & Furious 2 movie, which (to me anyway) doesn't seem to have as tight tolerances or quite as accurate castings.  Each issue has a lot of info about the 1989 - 1993 Skyline range and other Nissan models from that era, but the focus is on the BNR32 Skyline GT-R Nismo and the various racing it did in Japan, Europe (Spa 24hrs) and of course Australia. I've included some text translated with Google Lens in some photos and will add to them if there's anything worth including. 
    • If it's for a SR20, make sure it's not the American Poncams, might as well call them Poocams. Had a set in a friend's car, all scuffed up after a few track days. Like the metallurgy Tomei USA used is junk. Went back to JDM OG Tomei Poncams, no issues till now.   Tomei USA is not the real OG Tomei.   Random rant over, fk the US of A, bunch of c u n t s. 
    • Most of the industry in North America either runs on Siemens or Allen Bradley. I have two redundant S7-1500's on my desk right next to me for simulation. Siemens has been losing ground though since Stuxnet, as cybersecurity is a big thing. In my line of work that is federally regulated, you must by law have a cybersecurity management program in place and its audited and inspected every so often.  I work with Emerson PLC's daily (RX3i's) and have done large biogas/refinery projects with their DCS's. Their PLC's are somewhat OK minus the way they do PLC redundancy (You have to download on both PLC's separately every time you make a change )  As for their DCS's... you'll be limited financially first before anything else stops you. Costs are exorbiant at roughly 10x what it would cost you to do with any other system (e.g AB PAC).  1990's, those suckers are brand new haha! Kraft-Heinz (An old client when I use to work for an ESP) still runs Siemens TI505 PLC's from the mid 80's. Ohh how I don't miss working with those... you could only do a certain number of online downloads until it's "Change" buffer would be full and you would then need to go offline to do a full download. There was no warning of when this was coming up and it generally would happen when you would go in at 2am to make changes before production -_-.     
    • Unfortunately, not only is that not the case, one of the main "Selling points" of safety over comms is they clearly state in writing that there's no need to segregate safety networks from non-safety networks. It always gets intermingled with everything else on an ICS/OT network. 
×
×
  • Create New...