Jump to content
SAU Community

R34 Gt Engine Advice

Booted34

By Booted34,
in General Automotive Discussion

 Share

Recommended Posts

Booted34 Apprentice

Booted34

Posted
Posted

Hi all!

I'm new to SAU and was interested in some advice. I have a 34 sedan with GTT brakes and suspension fairly well sorted out. In the future I am planning an engine swap. What do people think of an Sr20 instead of rb25t. Why?

To save weight over the front end. To reduce overall weight. To give better power to weight ratio I am not interested in huge power, the car is a daily driver, of course I want more power than what I have.

I know they don't sound as good but I'm not to worried. As I drive on freeways a bit as well as windy roads I was thinking the s15 6 speed. I know its not strong but as I said I am not interested in big power just a nice balanced drive. Any advice is greatly appreciated thanks!

Link to comment
https://www.sau.com.au/forums/topic/387547-r34-gt-engine-advice/
Share on other sites
mad082 Grand Master

mad082

Posted
Posted

just stick with the rb25. while the sr20 is a decent motor, it is lacking in torque compared to the rb25. the weight difference isn't that much when you look at power to weight ratios of the entire car. cost wise it's probably a lot cheaper to use the rb25, and i dare say a lot easier to do the conversion. using the 6 speed would also result in you having to change gears more often than the 5 speed, and when sitting on the highway the actual revs it sits on at the speed limit won't be that much different.

Booted34 Apprentice

Booted34

Posted
  • Author
Posted

Thanks mate! I appreciate your advice. In case you're wondering i was thinking that i would have much more power and tourque than what i currently have with a sr20. You made a good point about trying to keep the conversion simple though. Maybe I should stick with an rb. As for the gearbox I don't mind changing gears and because of the gearing on the car I find myself looking for 6 th often. I guess you can change the diff ratio but then I could miss acceleration. I am thinking of fuel economy too. I thought maybe a vq35 6 speed with the RB? Thanks again!

mad082 Grand Master

mad082

Posted
Posted

Thanks mate! I appreciate your advice. In case you're wondering i was thinking that i would have much more power and tourque than what i currently have with a sr20. You made a good point about trying to keep the conversion simple though. Maybe I should stick with an rb. As for the gearbox I don't mind changing gears and because of the gearing on the car I find myself looking for 6 th often. I guess you can change the diff ratio but then I could miss acceleration. I am thinking of fuel economy too. I thought maybe a vq35 6 speed with the RB? Thanks again!

you seem to be a bit mis-understanding of the 6 speed gearboxes. they haven't simply taken a 5 speed box and added in a taller gear for 6th. what they have actually done is made every gear shorter than the 5 speed. you will find that 5th gear on the 6 speed box is a 1:1 ratio, which is the same as 4th on the 5 speed box, and 6th on the 6 speed box is only about 5% lower than 5th in the 5 speed box. so in reality, if you were at 2500rpm in 5th in the 5 speed, you would only drop down to 2375rpm in 6th in the 6 speed. (that is based off using the same diff ratio)

Booted34 Apprentice

Booted34

Posted
  • Author
Posted

Thanks I had heard the ratios in a 6 speed were lower. I am planning to change the diff anyway, so I could choose a lower ratio whilst I'm at it. Couldn't that work? Sorry to be a pain at this point I am just keen to improve the car as much as I can whilst I do the conversion.

mad082 Grand Master

mad082

Posted
Posted

i could write another long post pointing out the negatives of using both the SR20 and the 6 speed, but i could be bothered. just stick a rb25det in there and be done with it. a sr20 with 6 speed and taller diff is going to be crap to drive. the r34 is heavier than the s15 so 6th gear isn't going to be that useful. the slightest hill and you'd probably have to either floor it, or drop back a gear.

  • 1 year later...
  • 5 months later...
Ares180BPM Explorer

Ares180BPM

Posted
Posted

Slip light is to let you know wheel slip has been detected and that traction control has kicked in to correct it.

When i changed to an aftermarket ECU the traction control stopped working all together, so i took the bulbs out for both TCS and Slip.

If you haven't changed your ECU, you may want to get a diagnostic done to find the fault code and hopefully get it cleared.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • jtha7
      Replacing turbo water line - any recommendations or advice?

      By jtha7 · Posted

      Hi all, Restoring r33 series 1 rb25det. All the heater hoses were on their way out, have replaced them and put it all back together. After testing I noticed a small leak from behind the head on the actual metal water line to the turbo when cars warm. I tried running a longer hose over it but it kept leaking...   I am about to take the (stock) manifold off again😔 to change the water line does any one have any lines they recommend? I was looking at Aeroflow Turbo Oil & Water Line Set but not sure what everyone else recommends. Car is completely stock but want to upgrade turbo eventually. it looks like ill have to disconnect a lot just to replace these lines so if there's anything else recommended to do please let me know. Thank you in advance!
    • MBS206
      RB20DE NEO smallbox clutch.

      By MBS206 · Posted

      From memory, on the R33 GTSt at least, while everyone says "It's not adjustable", I found when I changed clutches in mine, it just needed a small adjustment on the rod length. But be very wary here, as you could end up trying to push the pushrod in the master too far, or blowing out the slave.   Most likely though, if the master/slave isn't bypassing internally or leaking out, then the throw out is the wrong height compared to the fingers on the clutch, so when it moves to disengage the clutch, it isn't 100% disengaged. You can check part of this out too by jacking the car up, having the engine running, put your foot on the clutch and try to engage 1st gear. If it goes in pretty easy (Compared to the ground) and/or the wheels start turning a fair bit and it takes a bit too much brake pedal to bring them back to a stop, this is likely the issue.  I'm not sure if you can adjust the height of the forks etc in these though, it's been that long since I've touched any RB gearbox.
    • MBS206
      Lock up the old for sale / wtb threads.

      By MBS206 · Posted

      That's all good, I thought I was missing some interesting feature! Maybe @PranK can double check if that is something that is meant to be operating or not.
    • Kapr
      RB20DE NEO smallbox clutch.

      By Kapr · Posted

      I hope that is not something that bad. From what i remember he said that only first gear is "hard" to get in and that he has couple of ideas what to try next but idk 😕  hope it is not gearbox out. I will let you know.
    • GTSBoy
      RB20DE NEO smallbox clutch.

      By GTSBoy · Posted

      If it's not the hydraulics, it is probably gearbox back out. Usually as per @Duncan's post, or otherwise associated with not getting the throwout fork positioned correctly. All the way up to catastrophically bolting shit back together without it being aligned properly and wrecking the clutch/input shaft/flywheel/something else.
×
×
  • Create New...