Jump to content
SAU Community

Recommended Posts

Be hard pressed to pop 1st gear. The front diff is the issue. Ash knows ;)

Yeah that's a rather expensive one.

I'd suggest anyone wanting to do a lot of launches, look into doing a Nismo front diff first... Before the stock one dies and then takes out your 9ltr sump as well, it hurts the budget allocation :closedeyes:

Yeah that's a rather expensive one.

I'd suggest anyone wanting to do a lot of launches, look into doing a Nismo front diff first... Before the stock one dies and then takes out your 9ltr sump as well, it hurts the budget allocation :closedeyes:

ohmy.gif

Is Mr limiter launcher getting scared???

Time to upgrade Deano

Haha the amount of driving my car has been doing for the past 6months, im positive its going to be fine.... it cant break itself, parked up in the shed with the covers on..... hehehehehehe

hey guys quick question , i rang horsepower in a box earlier and he was trying to say -9 is bigger than -5 and smaller than -10 yet the rated power is 330hp or there abouts , what turbo am i thinking of that is smaller than -10? if there is such a thing?

hey guys quick question , i rang horsepower in a box earlier and he was trying to say -9 is bigger than -5 and smaller than -10 yet the rated power is 330hp or there abouts , what turbo am i thinking of that is smaller than -10? if there is such a thing?

pinch.gif . Noob!

hey guys quick question , i rang horsepower in a box earlier and he was trying to say -9 is bigger than -5 and smaller than -10 yet the rated power is 330hp or there abouts , what turbo am i thinking of that is smaller than -10? if there is such a thing?

Lol are you stupid? from what you just said 10> 9 > 5

Hence 9 and 5 are both smaller than a 10

I don't think what you said is correct though.

Edited by Rolls

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Duh... to answer my own silly question, it's actually described in the FSM... ...400 pages away at the end of the manual, for RB25DE/DET signal descriptions, it cites the TPSwitch signal action, is dependent on the TPSensor value ~ this tends to infer the builtin POT voltage signal is the primary, and the switches are fallback/secondary should the POT fail/TPSensor signal lost (and switch alone with no TPSensor signal allows for base idle speed setting).... makes sense... they (TPS units) used to fail/wear the POT with time, they're not exactly built to last ~ having the switch as a redundancy gets around this...(or, it's less likely both signals would be lost as they're on different power rails)... and of course wrt RB26DETT, you have to electrically disconnect the IACV solenoid from the harness, to defeat idle air control...  
    • Dose is unaware just how much fun 145-150kw would be in a 2.5L NC MX5. It would be one of the most fun things to drive to ever grace SAU.
    • Same thought crossed my mind ~ depends on how one connotes 'stalling'...ie; gets a rough/stumbling idle as it get warm until it stalls... or... idles ok and simply falls-over when it gets to temp... ...you can test the whole circuit with a couple of resistors ...unplug coolant temp sensor, bridge terminals with a 2K7 resistor (ECU will do cold start), or with engine warm bridge with a 330R resistor (ECU will consider engine to be at normal operating temp)...it's a quick way to check wiring integrity/ECU response when you don't have a multimeter handy ...
    • They also make them with the motor mounted on the side 
    • Just be warned that that turbo will not be a direct re-fit to the car. The exhaust housing is, of course, in the same place. It has to be - it's bolted to the exhaust manifold. So the dump will fit up. But the centre housing is not as long, so the comp housing will move backwards. This will affect both the turbo inlet and the outlet. There is fab work that needs to be done. Yes. it has one, it should have one. Paper gasket.
×
×
  • Create New...