Jump to content
SAU Community

Recommended Posts

I'm not sure what psi is in the tyres.. I should have checked actually.. What sort of pressure should be around

My first run I dumped at 5 and it bogged

2nd run was around 6 and it took off

Might try 6.5 this time around

Did you miss the conversation about the inlet temperature probe?

We have a WINRAR!

Unless for some reason you are backing off before the line, clutch slipping heavily... 118mph is nowhere near 370rwkw. Infact it's almost 10mph down.

Easy to compared my 33GTR which was doing 122-123mph with 330rwkw and -9s and a 1.9 60ft. In my experiences the quicker the 60ft, the lower the MPH is also.

Interestingly MPH has shown a few other setups recently to be quite down on the claimed power.

doesn't necessarily mean you were on a happy dyno either. If you get some datalogging setup next time you hit the track it would go a long way, could be an unusual situation like boost drop or retarded timing. Either way the car was making low power on the track tonight.

Ash 123mph is very fast for 330kw, what traps did you run at 365kw?

Edited by linkems

^ yeah exactly. Car just doesn't have the power, by a very long margin is all the point is really and MPH shows that in most cases.

122-123 seems about right for 330rwkw in a R33 GTR going by the drag section results so I wouldn't say it was abnormal.

Never ran with 365rwkw/-ts unfortnately. I did do Motive DVD drag battle (airport) with -5s and some martini fuel but we weren't sure the power was right, had spark plug issues and then broke a diff... Not long after the clutch was dead as well... Fun of drag racing, my love of 8000rpm launches & 4WD circle work :laugh:

Did you miss the conversation about the inlet temperature probe?

Must have. Too busy day dreaming

Hopefully the wasps didnt fly too far away

I see what you did there

But seriously, shouldve run a low 11. Im sub 320 and ran 11.8 with a highest trap of 120

Jez, get this man on your dyno!

Edited by Hadouken

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi all. Been a while but things are moving along. I just have something that I am wondering about. Since I will use OEM turbo oil pumbing, I got myself a new bolt, the one that goes into the engine block oil feed. As I recall (and see visually) this bolt comes restricted with I think a 1.7mm hole? Not quite sure but it was something around that size. The turbos have 1mm restrictor bolts installed, as necessary due to ball bearings and my higher oil pressures. Can I now just use that OEM bolt with the 1.7mm hole in for the engine block or will this actually be too much oil flow restriction and I have to drill it out first? In my head it would make sense for the bolt to be at least 2mm wide as both turbos take "1mm of oil flow". Do let me know if my logic is flawed here, I just want to make sure I don't kill my turbo bearings with too little oil. Don't know if I can trust the saying I read somewhere that ball bearing turbos essentially only need an oil mist
    • There are several aftermarket options available, from not-too-painful moneyhttps://justjap.com/collections/driveshafts-bearings/products/d-max-reinforced-replacement-rear-driveshaft-set-fits-nissan-s13-s14-s15-r32-r33-r34-c35 and  https://justjap.com/products/crank-motorsport-billet-rear-axles-fits-nissan-skyline-r33-gts-t-r34-gt-t?srsltid=AfmBOorQk4xkGUa98kO7v2ePLUiNt-HRrM2AwWNw9mbSIVE1ujBVwY__, all the way up to The Driveshaft Shop https://driveshaftshop.com/skyline-cv-axles/
    • Yeah based on old XRC5964S specs, it looks to be roughly GTX3576R sized? But this 5964S compressor will flow 90lb airflow somewhat similar to the compressors in both the GTX3584RS or G35-1050.. I fully expected the 0.64 rear A/R to choke up top - seems way too small from typical convention - but these are seemingly beneficial over the prior 0.82 results.. Be interesting to see if he comments on the EFR question in that thread - he mentioned in a prior video that BW EFR's were the "cats pajamas 10 years ago", but by the sounds of things all his kits have been using Xona for quite a while now.
    • Yeah it’s still got the oem manual gearbox and clutch, only kinda mods are a blow off valve, coil overs, and a aftermarket intercooler. Also had it for about 2 months now with a lovely midnight purple paint on it.
    • Yeeeppp, been following a lot of the testing on the latest Xona stuff and there are some mental results.  He also went over 1000hp @ 4 hubs on his Mainline with a XRE6364S (63mm) which was also well into the 20psi range before 4000rpm on a 2.5. Crazy stuff. Fwiw the XRE5964S is basically the modern equivalent of their old HTA3582 - would drive nicely enough on an RB25 or 26, but proven capable of a huge amount of power if you want to spicy with rpm tho even at sane boost levels will make stout numbers 
×
×
  • Create New...