Jump to content
SAU Community

Recommended Posts

This probably has happened before to someone and hopefully someone can point me in the right direction.

Last month I got my Power FC installed and car tuned at Ultimate. When it was tuned the guys noticed the engine light flashing, and tuned it for the knock the Power FC was telling them. Now under slight load, the light flickers, but no I can't hear any sign of knock in the engine.

They did suggest to run a few bottles of injection cleaner through the system, but that hasn't made any difference.

I also did some research but still can't put any one finger on a problem. So any advice would be appreciated on how to fix it. They did offer a retune at no extra cost, but I want this problem fixed before it goes back.

Cheers guys.

Link to comment
https://www.sau.com.au/forums/topic/387982-something-very-confusing/
Share on other sites

what knock is the powerfc showing on the hand controller? 60+ will flash the check engine light

is the engine water temp getting to 100+? this will also bring the check engine light on.

does your exhaust still have the cat temp sensor? from memory in the R32 this detecting the exhaust is too hot will turn on the check engine light.

I have GReedy temp gauges for front and rear of the engine and it does go above 100 degrees and I will have to check the exhaust. But the temp on the stock gauge does read normal. And have never had the knock go above 60.

The car does run 98 all the time.

And the tune was about $560 from memory, but that was also them installing the power fc and boost controller.

The tune was done a month ago.

I know the knock it has isn't as good as it should be, but finding out whats wrong with it is extremely hard as noone can put a finger on it, or point me in the right direction.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Plazmaman 76mm Pro Series, done. Data to back it up, I posted up somewhere here a few years back
    • So.....wire it up appropriately. You can't use the resister pack with those injectors anyway.
    • that’s the thing i’m on ID1050s and haltech not getting power due to the injector resistor 
    • ahh okay cheers, i was thinking of just going for the m073, think m079 would be way too overkill considering they are same size. 
    • My first car was a HG. I'm very familiar with them. A mild cam upgrade is a good idea. The 186 is a very flexible engine - meaning it has good torque from down low. You can give up a little torque down low for quite a lot more excitement in the mid range, and a bit more up top - but they are not exactly a rev monster. You need to upgrade valve springs at the minimum. For a bigger cam, you'd want to make sure it wasn't still running the original fibre cam gear. That would be unlikely, given that most of them shat themselves in the 70s and 80s, but still within the realms of possibility. Metal cam gear required. Carbies are a huge issue. The classic upgrade was always a Holley 350, which works, but is usually pretty bad for fuel consumption. The 186S had a 2 barrel Stromberg on it that was very similar to the one on the 253, and is a reasonable thing if you can find one, and find someone to help you get it set up (which is the same issue with setting up a 350 to work nice). The more classic upgrade was twin sidedraught CD type carbs, or triples of same, or triple Webers. The XU-1 triple Webers being the best example. You can still buy all this stuff new, I think, but it's a lot of coin to drop. And then the people able to set them up are getting fewer and further in between. There's still some, but it used to be everyone's** dad and uncle could do it. **Not everyone's! But a lot. All in all, I wouldn't get too carried away with the engine. Anything you do to it without a full rebuild for power and revs will only make it slightly faster. I am all in favour of a complete teardown rebuild, with nice rods and pistons, 10 or 10.5:1 compression, and a clean port job with at least a big enough cam to run 98 with that compression, if not bigger. And if I did that to a dirty old red motor, I'd want to inject it too, which I'd struggle to fight against the devil on my shoulder that would argue for ITBs and trumpets. But the bills would start to mount up, and it will still never make stupid power. OK, a few people still know how to build absolutely mental red motors, courtesy of the work that went into HQ racing and modern knowledge being applied. But even a 300HP red motor is no match for an RB20 with a TD06. So you have to decide what it's worth to you. I'd just put a set of 6>2>1 extractors, a 2.5" exhaust and an electronic ignition conversion/dizzy on it and just run the old girl like the fairly slow old girl that she really is.
×
×
  • Create New...