Jump to content
SAU Community

Recommended Posts

Hopefully this has'nt been answered, but I am about to finish all my refit of my s1 rb25 and I need to confirm about the timing belt tensioner, the spring is meant to adjust the belt correct?, so i did this and it doesnt hardly even move the belts slack... Am i meant to wind up the spring before fitting it over the stud it sits on? I set my belt with an allen key, but im worried about tension. I set it last time too tight and it was making a whirring sound, I want some reassurance/help with this because i have a near 20k motor that I dont want to **** up. Thanks

The Nissan manual says to put the engine on TDC and loosen the nut on the tensioner. Do 2 full laps of the crank and stop back on TDC. Then tighten the nut on the tensioner (use an allen key to hold it in place). I've done it this way on 3-4 cars now, and it works a treat

None of that info helps if he hasn't got the tensioner spring doing its job.

Yes you have to preload the tensioner to get the spring working, otherwise it will just sit there as you found out.

Take care you don't get any windings gaught under the tensioner where it mounts to the block, that will cock it over and run the belt off.

Next as it's a Gates belt, my opinion is that the workshop manual info won't work, the belt gets too tight once things reach operating temp.

From experience Gates belts have to be setup looser than the factory belt, which is why no more Gates belts for me.

You need to be doing belts daily to have the "feel" for Gates belts.

I did mine by relaxing the tensioner and turning the harmonic balancer a few revolutions. The tensioner will than move into the correct spot and all you have to do is keep pressure on the belt and tighten the tensioner up. Hope that helps ( I was told this by 3 different mechanics so hopefully its right as i had over tensioned mine as well the first time ) Had no problems what so ever

jiffo's right, I know how to rotate to set and all but my spring itself isnt right, it holds all but zero tension on the belt. Its not damaged just not coiled up....

So when it used to whir with my first build, it was obviously too tight, so can it be all but whirring? I realise what a loose belt ends up doing, but what does a slightly too tight one do?

Thanks for the input though guys

Mate does it have the stud in the block that the spring rests on to put tension on the spring? If yes then your probably just not locating the straight part of the spring correctly. A belt thats too tight causes a few problems but most noticeable (what i see on engines that have been built by others that ran belt tight) is excessive wear on the 2 very front cam bearing tunnels, the one which holds the seals, its always on the inner side as the belt is trying to pull the cams towards each other. Belts also tend to go shiny when too tight. I usually run about 4 deg play. ie: wind the engine over by hand (breaker bar) until you pass a compression stroke (doesnt matter which cylinder) but you'll feel belt looses drag. rock the crank back n forward n you should have about 4 deg play...Hope that doesnt confuse you too much but its not that difficult. Just take your time ;-)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 馃槈. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 馃槏.
    • Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 馃檹 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 馃槈. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 馃槏 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
    • I've managed to find this: Nissan_Stagea_AutechVersion260RS (1).pdf
    • I believe @Duncan has given it a crack at Mt Buller before (in actual race conditions)
  • Create New...