Jump to content
SAU Community

Recommended Posts

I found and run the test, but unfortunately did not show up anything, does anyone know where the water control valve is, i presume its an electric solenoid type hidden away somewhere??

Climate Control Diagnostics R32 and R33

The climate control has a diagnostic mode.

Enter the diagnostic mode by pressing the OFF button for five seconds within ten seconds of

turning the ignition on.

Sensor check

Sensor check is selected by pressing HOT switch (the red triangle) while in diagnostic mode.

The microcomputer detects whether each sensor input signal is within correct parameters. The

results are displayed on the screen.

If normal, a "20" is displayed.

If abnormal the failed sensor number is displayed. The sensor numbers are as follows:

20 - all is normal

21 - outside air sensor

22 - Inside air sensor

23 - Water temperature sensor

24 - Intake temperature sensor

25 - Sunload sensor (small sensor on the left hand side of the dashboard near the windscreen)

26 - PBR

27 - Refrigerant temperature sensor

This should tell you if any of your sensors are faulty.

Mode door position check

(This is probably not the cause of your problems but it is a nifty self check to play with).

While in Sensor check, depress the HOT button again. This will operate the the mode door

actuator, and checks the whether the position detection switch is operating. Again the results

are displayed on the display.

If normal, a "30" is displayed.

If abnormal the number of the faulty mode is displayed as follows:

30: Normal

31: VENT

32: B/L (Bi level)

34: FOOT

35: DEFROST/FOOT

36: DEFROST

Link to comment
https://www.sau.com.au/forums/topic/3883-no-heat/#findComment-62873
Share on other sites

Originally posted by inark

its 1am... but im going outside to have a fiddle with it just cause that looks like fun haha

lol yea i like fiddling at 1 am too...

sorry i cant help u there jethead. i did the test and 25 - Sunload sensor seems to be faulty....bo my question is, what does it do, and is it important???

Link to comment
https://www.sau.com.au/forums/topic/3883-no-heat/#findComment-62925
Share on other sites

Originally posted by inark

its 1am... but im going outside to have a fiddle with it just cause that looks like fun haha

You should have got error 25 (Sunload Sensor).

Word of caution, even in shade on a bright sunnny day you can get error 25.

Link to comment
https://www.sau.com.au/forums/topic/3883-no-heat/#findComment-63194
Share on other sites

Originally posted by skyline33

leon,

I thought you fixed it

errr the guy that sold it 2 me did....but then a few dayz ago it made that sound again.... :) I don't wanna go back 2 him and get it fixed again..u said u know someone that can fix those stuff right? Need some help man

Link to comment
https://www.sau.com.au/forums/topic/3883-no-heat/#findComment-63498
Share on other sites

yer..it was the gate thingy that heat your windowz when it goez foggy....it wasn't moving properly.....it still workz though, just makez that annoying sound..... And I dunno y but I get hot feet instead of cold feet...heater is on no matter I turn it off :) weird shit....

Link to comment
https://www.sau.com.au/forums/topic/3883-no-heat/#findComment-63503
Share on other sites

On the righthand side of the gearbox tunnel Adjacent to your left foot is an servo/motor mechanism that sequences the buterflies and water valve via a push/pull cable. This mechanism was stuck, gave a bit of a helping hand and away it went, all is fine now. Fault code 26 then dissapeared, left with Sunload sensor fail but who cares...Ive got heat now..

Can someone tell how to identify/find the Sunload sensor????

Link to comment
https://www.sau.com.au/forums/topic/3883-no-heat/#findComment-63513
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • does anyone know tie rod torque setting and anti roll bar for r34? Is there a workshop which shows various components torque setting?
    • Hi    have purchased pair of eibach wheel spacer as I couldn’t fit set of wheels I bought for my car due to it catching caliper.   I know I need to cut the bolts on my discs so they sit flush with the nut supplied but the nut doesn’t sit all the way into the groove meaning wheel would not directly fit onto the spacer rather the nuts. Any thoughts?   See pic   https://ibb.co/VJK5w5G
    • Nah. There's not shit tonnes of pressure in there. Just drill with a 1.5mm drill or something equally tiny. When the drill goes all the way through thee gas will start to come out, but with such tiny path through the flutes of the drill bit, it won't be at all dangerous. You can be as paranoid as you like from then on. I'd just pull the drill out while keeping my face out of the line of fire. But then, I spend half my time looking into pressurised furnaces. So my risk acceptance is somewhat higher than most!
    • Been needing a new clutch for a while, but holding off because of life tingz and adulting. But... Being of Asian descent, I can't pass on a good sale, especially everyone else is selling it for $2k+ (JJR has it for $1799). Really on the fence on this one, because the unsprung version of this is $1281 via Shitbox (Sparesbox) and the sprung version is quite a bit more (no idea why Shitbox doesn't offer them). Ending up just sending it and getting the twin sprung organic. Mainly because I wanted the car to be nice to drive and didn't want to make it more of a shitbox than it already is.    
    • It was the pressure I was worried about. @GTSBoy does drilling them pose any problems?
×
×
  • Create New...