Jump to content
SAU Community

Recommended Posts

does anyone have a guide on the correct procedure to remove a series 2 rb25det engine from a r33 in the correct manner. i can pull an engine no problem but i just want make sure i dont run into any snags along the way. as i only have 2 days to do it.

thanks

Link to comment
https://www.sau.com.au/forums/topic/388552-gtst-engine-removal/
Share on other sites

I don't imagine it would be too difficult mate

Remove gearbox, disconnect exhaust, plumbing, wiring loom, fuel lines, coolant hoses and radiator for more room

Remove the nuts from the engine mount studs and pull it out :)...

I'm sure there's a couple of other little things but that's the most of it

Drain all the fluids first too ;) except clutch and brake of course

Do a GTR, now that's a pain in the ar$e lol

ok im looking for help not smart arse comments, yes i could take it to the shop im not retarded. the idea is A. so i save some money! and B. i can do with the experience of learning as most of you guys complain " oh the new guys to imports dont even know a there way around a car they just take it to a mechanic and say make my car fast" well herei am trying to learn how to do it myself. right o

I don't imagine it would be too difficult mate

Remove gearbox, disconnect exhaust, plumbing, wiring loom, fuel lines, coolant hoses and radiator for more room

Remove the nuts from the engine mount studs and pull it out :)...

I'm sure there's a couple of other little things but that's the most of it

Drain all the fluids first too ;) except clutch and brake of course

Do a GTR, now that's a pain in the ar$e lol

that last comment wasnt directed to u mate, thanks for the help

maybe you can also help yourself though by doing some research first though...

http://www.skylinesaustralia.com/forums/topic/41121-removing-a-gtr-enginegearbox-plus-more/page__p__843424__hl__engine__fromsearch__1#entry843424

yep its for a gtr but it should still be fairly similar

pretty straight forward, unplug everything wiring loom related, remove intake piping/intercooler/vac lines/radiator/clutchfan or thermos, unbolt and tie out of the way AC compressor and power steering pump, remove gearbox bolts (ones up the top are dream boats), attach engine crane, undo engine mounts from cross member, check you have everything free/clear/unplugged and remove it keep in mind the engine must come forward to get the input shaft from the gearbox out of the clutch.

maybe you can also help yourself though by doing some research first though...

http://www.skylinesa...__1#entry843424

yep its for a gtr but it should still be fairly similar

i have been searching all day all i can find is gtr manuals. thats why i posted here,

I have just rebuilt my engine and i couldnt find a written procedurethis is what i did.

Disconnect battery Remove Exhaust dump pipe to tail pipe drop engine coolant and remove radiator

Remove plastic around shifter and remove shifter cover & remove g/stick

Disconect neutual and reverse switch connections also remove clutch slave cylinder and tape it togeather so it doesnt leak zip tie it out of the way

Undo tailshaft but dont remove Jack and support rear of engine so it doesnt hit the steering rack get it a low as you can as i had to use very long extension bars to get to the bellhousing bolts remove transmission with tailshaft connected so not to loose oil. Also keep engine supported.

Disconnect Engine wiring loom oil switch steering switch air cond wire. Undo heater hoses turbo to air filter brake booster vac hoses fuel lines disconnect pwr steering res and drain

Unbolt and remove pwr steering pump and braket. Also unbolt air cond pump and bracke zip tie out of the way.

Undo engine mount nuts and remove engine

refit engine in revese order

I hope i havnt forgotten anything

ote name='riley' timestamp='1326791310' post='6192287']

does anyone have a guide on the correct procedure to remove a series 2 rb25det engine from a r33 in the correct manner. i can pull an engine no problem but i just want make sure i dont run into any snags along the way. as i only have 2 days to do it.

thanks

Forgot on my last post

ALSO TAKE A COUPLE OF ENGINE BAY PHOTOS BEFORE YOU START THAT WAY YOU HAVE A REFERENCE FOR INSTALLING THE ENGINE AGAIN

does anyone have a guide on the correct procedure to remove a series 2 rb25det engine from a r33 in the correct manner. i can pull an engine no problem but i just want make sure i dont run into any snags along the way. as i only have 2 days to do it.

thanks

i find pulling the box out with the motor is much faster. unless you have a hoist with rattle gun and massive extensions to undo gearbox bolts.

mines a rb2530 with custom mounts and getting the the gearbox bolts are some what impossible.

Yep I pulled mine out with the box on.

i find pulling the box out with the motor is much faster. unless you have a hoist with rattle gun and massive extensions to undo gearbox bolts.

mines a rb2530 with custom mounts and getting the the gearbox bolts are some what impossible.

The ones i hae done we pulled them with the box attatched. Much faster :) Just dont forget the clutch line :)

But as suggested its the same as every other engine. Unplug plugs, un-do hoses.

If its a stock turbo, then removing the turbo and dump pipe in one piece is highly recommended :) SO much easier than undoing and doing up those assf**k dump pipe bolts lol. It can be done.

as said leave the gearbox attached. leave p/s, air con and clutch slave all attached to their lines and unbolt them from motor/box so you dont have to deal with any of the fluids. make sure you pull it out somewhere with plenty of height clearance as you'll need to get a fair bit of angle to get the box out aswell.

best bet for getting it done quickly would be to find someone on here local to you and pay them with beer to give you some guidanc. once you know what your doing you can go from complete running car to motor on the ground with box off in around 2 hours working at a steady pace, rushing just leads to losing skin....

Edited by JonnoHR31

i loved my SR20 use to have the motor & box out within 1 1/2 hours. when i changed the clutch i use to rip the motor with box out together done in like 5 hours and driving LOL

the RB does take longer but once you do it a couple of times it gets faster

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Great interview on damper settings and coil selection by HPA https://www.facebook.com/HPAcademy/videos/30284693841175196/?fs=e&s=TIeQ9V&fs=e
    • Yeah, it was a pretty deep dig.
    • The values for HID colour are also defined ~ see https://www.legislation.gov.au/F2006L02732/latest/text  ~ goto section 3.9 onwards ....
    • So, if the headlights' cutoff behaviour (angles, heights, etc) are not as per 6.2.6.1.1 without automatic levelling, then you have to have to have automatic** levelling. Also, if the headlight does not have the required markings, then neither automatic nor manual adjusters are going to be acceptable. That's because the base headlight itself does not meet the minimum requirement (which is the marking). ** with the option of manual levelling, if the headlight otherwise meets the same requirements as for the automatic case AND can be set to the "base" alignment at the headlight itself. So that's an additional requirement for the manual case. So, provided that the marking is on the headlight and there is a local manual adjustment back to "base" on the headlight, then yes, you could argue that they are code compliant. But if you are missing any single one of these things, then they are not. And unlike certain other standards that I work with, there does not seem to be scope to prepare a "fitness for purpose" report. Well, I guess there actually is. You might engage an automotive engineer to write a report stating that the lights meet the performance requirements of the standard even if they are missing, for example, the markings.  
    • Vertical orientation   6.2.6.1.1. The initial downward inclination of the cut off of the dipped-beam to be set in the unladen vehicle state with one person in the driver's seat shall be specified within an accuracy of 0.1 per cent by the manufacturer and indicated in a clearly legible and indelible manner on each vehicle close to either headlamp or the manufacturer's plate by the symbol shown in Annex 7.   The value of this indicated downward inclination shall be defined in accordance with paragraph 6.2.6.1.2.   6.2.6.1.2. Depending on the mounting height in metres (h) of the lower edge of the apparent surface in the direction of the reference axis of the dipped beam headlamp, measured on the unladen vehicles, the vertical inclination of the cut off of the dipped- beam shall, under all the static conditions of Annex 5, remain between the following limits and the initial aiming shall have the following values:   h < 0.8   Limits: between 0.5 per cent and 2.5 per cent   Initial aiming: between 1.0 per cent and 1.5 per cent   0.8 < h < 1.0   Limits: between 0.5 per cent and 2.5 per cent   Initial aiming: between 1.0 per cent and 1.5 per cent   Or, at the discretion of the manufacturer,   Limits: between 1.0 per cent and 3.0 per cent   Initial aiming: between 1.5 per cent and 2.0 per cent   The application for the vehicle type approval shall, in this case, contain information as to which of the two alternatives is to be used.   h > 1.0   Limits: between 1.0 per cent and 3.0 per cent   Initial aiming: between 1.5 per cent and 2.0 per cent   The above limits and the initial aiming values are summarized in the diagram below.   For category N3G (off-road) vehicles where the headlamps exceed a height of 1,200 mm, the limits for the vertical inclination of the cut-off shall be between: -1.5 per cent and -3.5 per cent.   The initial aim shall be set between: -2 per cent and -2.5 per cent.
×
×
  • Create New...