Jump to content
SAU Community

Recommended Posts

Hey guys,

After a long time thinking about the direction in cars I want to head in, I have sadly decided to sell my very first skyline.

I am the first owner of this car in Australia, purchased it in October 2008 completely stock from Kamikaze Motors.

I have purchased all the parts myself and had all mods installed by Le Mans Automotive in Templestowe.

Serviced every 5000KMs

1996 - ECR33 - GTS-T - RB25DET - Manual

141K on the clock

AR1 - Super Clean Red II / Nismo Racing Red

Factory Sunroof

Tein Mono-flex Coilovers

Hel Braided Brake Lines

DBA 4000 Front Rotors

Project Mu B-Spec Front Brake Pads

Project Mu Shims

Greddy Oil Filter

ARK Rev Shift Timer

ARK Advanced Boost Controller

Blitz FMIC - Return Flow CS

JJR 3" Bellmouth Front Pipe

X-Force 3" Stainless High Flow Cat

JJR Rear Strut Brace

Front Strut Brace - unknown brand came on car

JJR Hicas Lock Bar

O2 Sensor Replaced 10,000KMs ago

Autometer Boost Guage

Wed Kranze ERM 17" x 8.5" gtr offset 2.5" dish

Yokahama S-Drive Tyres

Sony CDX-GT170 black/red Headunit

Pioneer Carrozzeria Tweeters

Pioneer Carrozzeria 6" front speakers

Sony Xplod 6" 4 way rear speakers

Sony Xplod XM1S Amp

Sony Xpod boxed subwoofer with grille

Replaced windscreen 10000KMs

+Few other parts here and there

I will also be including

APEXi pod - used for 1000KMs

Nismo front lip - in silver

Series 2 optional black mesh grille with red S

collection of shift knobs

Stock R33 Wheels x4

Stock SMIC, brake lines, front pipe, cat, shims etc

I have receipts for everything and these are available for perusal

The car has never been to the track and boost never pushed above 8psi

seats always covered with seat covers

car has a small dint on bonnet, could probably be popped out very easily, and a 50 cent coin sized chip of paint off the front bar from someone reversing into me

im asking for $9750 ONO

Send through a private message if you have any questions

Thanks

post-55700-0-19494500-1327129819_thumb.jpgpost-55700-0-58323800-1327129871_thumb.jpgpost-55700-0-67688400-1327129881_thumb.jpgpost-55700-0-92484000-1327129898_thumb.jpg

Edited by bluejeans
Link to comment
https://www.sau.com.au/forums/topic/388959-r33-gtst-series-2/
Share on other sites

  • 2 weeks later...
  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • What can't be done with a little bit of decking board or similar timber bolted to a hub flange via 2 wheel nuts is not worth talking about.
    • I noticed something. On the tps sensor and the sensor behind the adjustment screw is adjusted towards the far left. Are these screws supposed to be centered? (this sensor was in the same position before the tune as well)  Also attached a photo of where my car usually idles at when warm (sometimes a tiny bit above that). I think I might have screwed up the calculation and it might have better than I thought lol at 750rpm still not 650rpm though.      
    • So for both general interest of engine health, and to rule out any coolant/oil issues, I organised an oil analysis done on the 125,000klm oil Results below, all good, just a bit of fuel dilution which I'm not too worried about
    • This is actually a really good way of measuring what wheels fit. If only there was a similar measurement between hub face and suspension :p That said, it's probably pretty simple to actually measure it all with the wheel off the car for the rear. The front is a bit more complex but.. 
    • Being the top Google search result for R34 wheel-related inquiries, lemme throw down my experience. I calculated that 100mm from hub face to wheel face is about the perfect fitment for my ENR34 sedan.  I've been running 18x8.5s, ET35, with a 1" spacer. So, 8.5in to mm = 216mm. 216/2 = 108mm. 108-35 = 73mm. 73+ 25 (1" to mm) = 98mm.  If you wanna get close to this on dif widths, here are the offsets you'll want: 9" - ET around 15mm 9.5" - ET around 20mm 10" - you're crazy, but ET around 30mm All these should fit perfectly on a non-widebody, non-GTR Skyline. Note that it's probably the absolute max, and you're probably better off running a couple degrees of camber in this config, but it looks great, super flush.
×
×
  • Create New...