Jump to content
SAU Community

Recommended Posts

  • Replies 219
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Its gay, we can't even write ideas because of people who would troll this forum to see what people could and would do to circumvent their detection methods. I don't understand the concept of how some cars can run 96db and others at 90.

My car idles quietly so I thought ill do a free rev to 5100rpm. There is no way in f**king hell ill pass. I can still hear the engine over the exhaust though.

Saw you on the road the other week, wtf is on your exhaust tips?

there's a ball of stainless steel wool in the tip, held in by some stainless mesh and clamps. gets rid of all the resonance. changed the muffler but it didn't cure it, so I did that.

I know it looks odd, but it worked and didn't affect economy or performance so.. meh

The main reason the price is so large is due to the time it takes to measure, cut and weld things together. What if you've already got an exhaust and want to get it modified to shut it up but maintain its flowing capabilities. Do you run in line mufflers and hot dogs/resonators or just a muffler at the end? Any photos of the exhaust or brand names of the mufflers used?

Yeah you can do that and it's cheaper. Basically it involves playing with mufflers. I have a custom magnaflow crossflow muffler in mine. Also using cross flow mufflers is good without any real restriction. Having a good mid muffler and an end muffler though would easily make it below legal limits (so basically you'd be making a stock style exhaust just all shiny and larger diameter. Otherwise it would be good if someone could make a varex type system but in a mid muffler with a recessed control box covered by a bolt on panel or something. That way it would be near impossible to tell. Especially if your exhaust is tucked up nice and high like mine is. Probably dreaming there though :P

If you're still keen I can post pics?

So basically anyone can get an exemption then? Can anyone think of a reason why Tomic would need to be given an exemption? The only thing that I can think of is because his smoking hot gf wont be seen dead in anything worth under $100,000.

All I can say is that I sympathize with anyone who says that it is not fair for him to get an exemption when most of you other young guys cant. I have no problem with people getting an exemption in certain situations ie. mechanic etc. but I cannot think of a single legitimate reason for Tomic to get one.

Apparently the M3 is given to him by BMW Australia and he is able to drive it for any situation tennis related (work) and for Tennis and BMW related (promotions). So basically I see that he is able to drive the M3 where ever and when ever he likes, especially as now is the Aust Open/Australian Tennis season looks like Tomic should get off all charges if this is true. Also depends how the Judge sees it.

I agree agree mate but its probably not that skinny pin head that they are interested in seeing the car its the blonde piece of hot sex thats sitting in the passengers seat beside him thats gunna sell beamers to cashed up middle aged men :thumbsup:

That's a crock of BS. As if advertising is worthy of an exemption, as if seeing a tool in an M3 is going to sell you an M3.

A woman at work here has an E36 M3 with the rego plates "R3SSOT" (TOSSER Backwards - so when you see it in your rear view mirror you know who's following you)

LOL :no:

And since when did you become NSW Prez Eric? Congrats.

We got my 4 inch exhaust down to 93db in street form with a very restrictive Euro 4 emissions cat. Still too loud for the test but a good effort I think.

Past the test with 84db with a straight through cat and a 'special' flange. Undetectable and 30sec to remove.

So the only way I can get done is by one of those mobile tester things like was on the ACA "news" story. With me only driving the car once in a blue moon I think my chances are almost nil.

Pretty much what we found down here :D

Good to see someone else in the same ball park, with similar results.

Amazing what a baffle does.

Just a baffle plate with a couple small holes drilled into it, effectively making exhaust 1"

Only good for EPA tests and not daily use. Also... "techincally" illegal unless it's welded in. Fat change of finding that out without taking the exhaust of though

If he had an exemption for sponsorship purposes then he is well within his rights to drive the car. I believe stopping him may constitute a restriction of business which would be against the law, similar to the Terry Hill ARL draft case from the 90s. Put yourself in his shoes he only has a limited time to take advantage of his ability to produce money all it takes is a career ending injury or a massive form slump and no more endorsement deals.

<br>are you his lawyer or his mommy?<br>
<br><br>Either one would be nice so I could get that cash.  <img src="http://www.skylinesaustralia.com/forums/public/style_emoticons/default/smile.gif" class="bbc_emoticon" alt=":)">

<div><br></div><div>Well from a quick google search he has exemption for "reasons pertaining to his career" so that could involve more than just training.</div>

Edited by Desavona

Problem is if it isn't factory - then valved exhausts are illegal as well. At least down here - so one can expect it to be in NSW, and the video is evidence of this :(

It's really stupid that many models of cars these days have them FACTORY and can be controlled MANUALLY.

Yet to do the same, to pass the same laws, if you or I did it to our cars... It's suddenly illegal.

>_<

It really just needs someone with the staying power (and money) to follow it through the courts and win. Set a precedent and then everyone else launches back at them. It really doesn't make sense a Ferrari can pass ADR with a valve, yet a Skyline cannot. The core EPA laws are from 1992, so very dated.

Also farked that Police can report you to the EPA without even MEASURING your car. They just have to report you based upon suspicion you 'might' be over, rather than actual fact. People down here have been reported when their car has been PARKED and not even running (as the notice tell you the time it was noted).

Really feel sorry for your NSW boys overall... The EPA are a bunch of over powered kents.

Mate, this happened to me.

I called up the manager of the Penrith EPA station and abused the crap out of him. This is guilty until proven innocent behaviour...the expected me to take a day off work, pay the test fee to clear the car.

The guy said they cannot enforce the law/regulation to the Police, it is up to them to enforce it however they see fit, so basically a blank cheque. He also said the cops are advised to book cars that are loud and not 'look/appear' loud but clearly that doesn't mean anything here.

All revenue-raising/keep RTA employees in a job imo.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Might also needs a stronger actuator with the right preloading. With older 2019 built bush G3 units, BB upgrade or 21U housing down size makes a pretty decent gain in response as well. 
    • Hey lads  so im finally putting together my rb30 forged bottom end and ran into an issue. I measured my main bearing clearance with arp main studs torqued to 60 ft-lbs using ACL H series STD size bearings and standard, un-ground crank shaft journals and got an oil clearance reading of about 1.3 thou measuring straight up and down and about 2.8 thou measuring at a 45 degree angle (just above and below the parting line). My machine shop said they measured the main tunnel and it was all within spec (they didnt say the actual measurement) and to go with a standard size bearing, which i have done and the clearance is too tight, I'm guessing because of the extra clamping force from the arp studs distorting the main tunnel. I was wanting to run about 2.5 thou main bearing clearance.  My questions are: 1. could i just use the HX extra 1 thou clearance ACL bearings? that would fix my straight up and down clearance making it about 2.3 thou, but then would the side to side clearance be too big at around 3.8 thou? 2. what actually is the recommended main bearing clearance for measuring near the parting line / side to side. i know its supposed to be bigger as the bearing has some eccentricity built into it but how much more clearance should there be compared to the straight up and down measurement? at the moment there is about 1.5thou difference, is that acceptable or should it be less? 3. If i took the engine block + girdle back to the machine shop and got them to line bore the main tunnel (like i told them to do the first time, but they said it didnt need it) what bearing size would i buy? the STD size bearing shells already slide in fairly easily with no real resistance, some even falling out if i tip the girdle up-side-down. If im taking material out of the main tunnel would i need a bearing with extra material on the back side to make up for it? this is probably confusing af to read so if something doesn't make sense let me know and ill try explaining in a different way. My machine shop doesn't come back from christmas break until mid January, hence why i'm asking these questions here. TIA for any help or info 
    • I bought the model back in Japan in Feb. I realised I could never build it, looked around for people who could build it, turns out there's some very skilled people out there that will make copies of 1:1 cars or near enough. I'm not really a photo guy... but people were dragging me in a group chat for the choice of bumper as someone else saw the car before it was finished as they are also a customer of that shop. I took the photo in the above post because I was pretty confident that the lip would work wonders for it. Here's some more in-progress and almost-done pics. It gives a good enough idea as to what the rear looks like!   I have also booked in a track day at the end of January. Lets all hope that is nothing but pure fun and games. If it's not pure fun and games, well, I've already got half an engine spare in the cupboard 
    • Well, do ya, punk? Seriously though, let's fu<king go! The colour and kit looks amazing on the car. Do you have any shots from the rear? I don't quite follow how the model came around. You bought the white kit and he modified it to match your car? Looks nuts either way!
    • So my car is finally back from paint! This took an absolutely insane amount of work and should get it's own build thread - but I didn't build it. It was completed by Troy @ https://scalekustoms.com.au/ I originally bought the AOSHIMA URAS Type R kit while I was in Japan, it's supposed to look like this when assembled: Now, I thought that was cool enough until I opened the box with Dismay, as there's no way I could possibly have completed it. The thing is 1/24 and has details down to the steering wheel horn button, which is a 2mm diameter sticker. I originally wondered if someone could make it at all, as is - But then things got a little carried away. It's worth noting that the model does not have an openable bonne, let alone engine bay, OR an openable boot. - Troy has worked wonders with 3D printer and presumably better eyes than I will ever have. My photos suck, so I will post up some of his in-progress ones he sent to me during the way. Unsuprisingly, he is very detailed. A lot of these are out of order. But he: 1) Made a LS engine and an engine bay appear out of thin air 2) Made the bonnet removable 3) Printed the rims I will buy in the future (or any rim you want) 4) Printed and added the wing that is going on 5) Tinted my back windows as this is what my car has IRL (privacy glass) 6) Added a licence plate. 7) Somehow did the interior 8) 3D Printed my actual seats 9) Made the exhaust under the car connect even though this is likely invisible. 10) Created a boot with my fking battery box, power steering reservoir, subwoofer and toolboxes back there. To say it's insane is an understatement. And I f**ked it all up because when I was re-mounting the wing (it broke in transit) I spilled glue everywhere and ripped paint up and Gregged the rear half of the car. Which about makes sense. Also, this arrived on the same day. Quite the change from: I spent 16 hours per day over the next 3 days pre-christmas putting the interior back together, mounting lip, fixing various bodykit problems with window mouldings, etc. and servicing, rebuilding my 370z brakes to go on the car 'soon', messing with heights to check clearances for new wheels, etc. I also had a foray into mounting wiper-mounted washer jets which was an absolute disaster. The bodyshop has welded (and painted) over the stock jet locations for reasons unknown to everybody (i.e they forgot) I also wanted to wire in the oil pressure sensor on Christmas Eve which was a BAD IDEA. You do not know terror like pulling your ECU apart, pinning in half-fitting pins that aren't the right ones, but trying anyway because it's Christmas eve, putting your ECU back together and having a no-start condition with a fuel pump not priming. Then you undo all your work and the fuel pump still doesn't prime. So after all that terror and horror and pain and tedious disassembly, the issue was the relay in the boot which seems to have died/stuck when I was turning the car off and on about 700 times testing shitty washer jets. I also re-wired the fuel pump power plug which fell apart in my hands. I am very happy I had 3 extra pre-made ones from a few posts/last Christmas's breakdown. https://bluewireautomotive.com/products/10-x-pcm-ecm-ecu-terminals I have put an order for these in, so I can actually add the pins to the ECU properly. The commodore ECU does not have the pins for Oil Pressure via ODB2. However the ECU can support it if you create the pins and wire them in. So for round two, and somehow attempting to route that into the engine bay through my impossible engine bay grommet is a fight for another day. It's 40C in Melbourne tomorrow, I am half tempted to drive the car with the aircon on to deliver presents to my partner's family and see if it helps with the overheating-on-40C-days-in-traffic-with-aircon-on-only issue that the vents were intended to solve. Do I feel lucky?
×
×
  • Create New...