Jump to content
SAU Community

R34 Gtr Owners, What Adjustable Arms Are You Using?

SS8_Gohan
 Share

Recommended Posts

zebra Grand Master

zebra

Posted
Posted

Meh. ALL my Ikeya arms are pillow balls and some have been in there for almost 4 years. They're fine.

People make out like they flog out in 100 km's. As for noise.... Can't hear nothing!

Your car has only seen 2 full days of driving time haha

But 20 years for rubber vs less than 10 for rose joints or less again for cheap shit ones

GTRsean Grand Master

GTRsean

Posted
Posted

Shhh, can't tell people :P. They are never on hand and always have to wait and order em in.

I have the castor bush kit with an offset pin for more caster, so i get to keep the light aluminum lower arms.

Whitle front and rear adjustable sway bars, and I just ordered the rear swaybar bearing link kit to go with it.

My 32GTR had whiteline sway bars too, and their camber correction bush kits. 6 years of use and the bushes were fine.

boostn0199 Grand Master

boostn0199

Posted
Posted

Whats wrong with whiteline? no ones mentioned whiteline except for sean.

I dont think whiteline do actual adj arms , they only have the adj bushes from what I have seen and those bushes are fine if you only want to make very slight adjustments as there is not much in them.

GTSBoy Grand Master

GTSBoy

Posted
Posted

Yuh, Whiteline bush kits are nearly useless for gaining adjustment more than about 0.5 degree (depending on which arm we're talking about). In addition, I replaced my original front caster arms that were fitted with Whiteline polyurethane bushes with some rose jointed adjustables. Even without winding in any more caster the car improved massively just because the squishability of the bushes was gone. Those caster bushes take a lot of force, and they do move a lot.

GTRsean Grand Master

GTRsean

Posted
Posted

I dont think whiteline do actual adj arms , they only have the adj bushes from what I have seen and those bushes are fine if you only want to make very slight adjustments as there is not much in them.

From the whiteline website:

http://www.whiteline.com.au/do_segue4.php?make=Nissan&model=Skyline&model_final=SKYLINE+R34+GTR+AWD&vehicle=11%2F98-02

Part numbers:

KTA 128

KTA117

Those are the one's I plan to use....

  • 2 months later...
SS8_Gohan Grand Master

SS8_Gohan

Posted
  • Author
Posted

just an update...

pulled trigger on a set of Cusco arms front and rear. Perfect fit (as expected) no farking around, but some issues though.... can't seem to run less than -3 camber no the front :( - rear is set about -1 which is about right for street for me, but as much as the turn-in is freaking nice with the current setup, i got adjustable arms hoping i could run street'ish camber and cranking some more neg in when needed.

is this normal for cusco arms? are they just that much shorter that you can't actually get 'a little' camber? i was kinda thinking like -1.5. on the fronts....

SS8_Gohan Grand Master

SS8_Gohan

Posted
  • Author
Posted

it's low but not that low, and the suspension place said the same thing. It looks low'ish but in terms of geometry etc it's THAT low... that's why i'm a little confused.... - if anything, i'd probably want to drop it some more

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Sean'O
      3D printing fun

      By Sean'O · Posted

      Howdy friends, So another weird one today, I was looking into replacing some broken clips holding the front grille for the R32 GTR (part number 01553-03831), and noticed the brackets which are supposed to hold the grille in place were also missing 😑. I do recall seeing this issue many years ago, but didn't fix it at the time. A quick look on eBay and I was able to find the genuine brackets, along with all the screws which suited the headlights (part numbers 26042-08U05,26092-08U05). Happy days!....  Once they arrived however there was an extra nut in the packaging which implied that there should also be a bolt or a stud, and sure enough, after a bit of searching I found this thread from 2013, and @Ants clearly shows a stud should be present. Reading around a bit more, it's possible the headlights on my car are the "povo pack" headlights as mentioned by @funkymonkey in this thread way back in 2008. This could explain why the studs are missing on my set of headlights. Looking at the headlight diagram I wasn't able to see a suitable part number for the stud itself. The headlight did indeed have a recess that looked like it would accept a stud, but interestingly no thread or anything obvious how the stud would be affixed to the headlight, I suspect it may have been glued in, press fit, or melted into the plastic at the factory. Another member may be able to clarify if they happen to have a genuine set of N1 headlamps. The only thing we have to work with within the recess is a keyway which likely is there to prevent the stud from rotating within the recess. In any case, back to 3D printing, I put together a model which acts like a pug with a friction fit inside this recess, making use of the keyway so it doesn't rotate while tightening a bolt. Printing in TPU will allow it to slightly swell making a nice snug fit without cracking the part. I've designed the adaptor it to accept an 20 mm M6 bolt (stainless with a cap head in my case), as opposed to the standard M5 stud and I made use of the standard galvanised split washer that came with the genuine brackets from Nissan. Once the bolt and screws were all in place, giving the bracket a gentle shake gave the classic "shaking the car" feeling, very solid, which gives me confidence this is going to be able to hold on much better than the janky solution which seems to have been here for the past decade or so. Overall I'm really pleased with how this turned out and maybe there are more people out there running these headlights without a centre stud at all! Link to the freely available model on Printables: Click here Regards, Sean  
    • GabsReDeal
      R32 GTS (RB20DE) clogged cat

      By GabsReDeal · Posted

      Hey everyone, This is my first post apart of the introduction. I tried searching a bit on the forum but couldn't really get a straight answer. I got the car to my mechanic as I felt it being weak. It seems that it was missing on two cylinders due to the injectors. I had all my injectors clean and the car runs much better. The mechanic also confirmed my suspicions that the cat is clogged and needs to be tackled asap. The cat rattles a bit and the hot exhaust warning frequently lights up when driving after getting the injectors clean. In my introduction I was asked about what modification I might be interested in and mentioned a cat delete. From what I was told, this is not really beneficial on the RB20DE and there are more cons than pros.  Could perhaps anyone give some suggestions on what the best course of action would be since the current cat is toast and needs to be removed/replaced anyway? I can also sometimes smell a strong smell of fuel, but I'm not sure if this is related.
    • Milkmun
      NC MX5

      By Milkmun · Posted

      Hope the cans went down well at least 
    • Milkmun
      Neil's R33 Gts-t Build

      By Milkmun · Posted

      255 can't go wrong with the price.
    • Kinkstaah
      Neil's R33 Gts-t Build

      By Kinkstaah · Posted

      When I was replacing my pump due to being stranded in the wrong state, I went with the Deatschwerks 320lph kit. It is a direct plug in to the stock wires, harness, everything. It comes with a plug... but you can plug the OEM plug directly into this thing. https://justjap.com/products/deatschwerks-dw300-fuel-pump-nissan-s13-silvia-r32-r33-r34-skyline-c34-stagea?currency=AUD Downside: Won't actually flow that much on boost if you want to push it on E85, but it's comparable to the 040/255 etc. Little more actually.
×
×
  • Create New...