Lloyd Smiths 1Uzfe Corolla Drift Car

[ecko]

Ladies and Gentlemen,the time has come to sell Lloyd smiths Ex Falken V8 Drift car

This car was completed in 2010 and has seen well over 30 drift events in the past 24 months and has been nothing but reliable making any and every event possible on the calander, You think the Motorfix V8 corolla is good, wait till you see/hear/drive this

Currently has 270kw and 700nm at 7400RPM

Notable achievments for lloyd in this car include

2010 Tas drift series 5th overall on debut year

2011 Power cruise Burnout comp winner (against 500hp big block burnout cars)

2011 World time attack 5th place qualifying

2011 Tas drift series 2nd place overall

Car article in Performance imports 141

Article in rereleased Drift battle magazine

Few snippets of action on Wreckem 2010

The full build thread is available to view here http://nissansilvia.com/forums/index.php?showtopic=431244&st=270&p=6262257&hl=lloyd&fromsearch=1entry6262257

Full specs as listed below

AE71 Toyota Corolla Chassis- Slant front

ENGINE

AZcustom 8 litre trapdoor sump

Factory Rods

ACL race series bearings

Custom ROSS pistons (once off made, Moulds were sent of head and block for design in the US of A)

Total seal Piston rings

Cometic Metal head gaskets

ARP head bolts

Head ported and polished

1mm oversized valves

Kelford Valve springs

Kelford 286 degree cams

Powder coated rocker covers

4age Blacktop Individual throttle bodies with custom velocity stacks/airfilters

Custom vacuum plenum with in car idle control

7MGTE 440cc Injectors

Bosch 070 Lift pump

AZcustom 3 litre surge tank

Bosch 044 feed pump

Azcustom equal length extractors ceramic coated chrome feeding twin 2.5" side pipes

AU falcon radiator

AZcustom header tank

OEX 16" thermo

AZcustom Catch can- mounted inside car

B&M oil cooler

Grex thermostatic oil filter housing

Power steering cooler

S13 PS pump custom mounted

Haltech PS200 ECU

Ba falcon ignition coils

New genuine rotor buttons, dizzy caps, leads

BKR6EKUB sparkys

Driveline

CRS Bellhousing

CRS lightened flywheel

Xtreme 260mm drift clutch

Rebuilt toyota R154, new syncros bearings seals etc

PPG Chromoly 3-4th gear selector

Custom 1 piece tailshaft

Locked Hilux diff- Multiple ratios available, 4.11 atm

Front Suspension/Brakes

- S13 crossmember moved 30mm forward compared to where holes usually line up for more caster without wrecking inner LCA bushes and no chance of binding due to the steering rack coming forward

- S13 steering rack with power steering

-NP offset rack spacers

-S13 lower control arms notched and boxed in

- Inner LCA pivots on crossmember re-drilled 30mm higher

- D-Project solid steering rack bushes

- JJR tie rod ends

- s14 tie rods

- BC Racing S14 front coilovers with 8kg/mm or 7kg/mm springs avalible

- S14 knuckles and hubs (5 stud)

- NP modified knuckles 15mm out 18mm in

- Modified strut tower tops to position strut tops further backwards and out

- SuperPro inner LCA bushes and caster rod bushes

- Custom front swaybar

-S14 front brakes

Rear Suspension/Brakes

BC Racing AE86 rear setup with 6kg/mm springs

- Custom equal length 4 links with SuperPro bushes

- JJR panhard rod

- Move panhard rod pivot down on diff

-Custom traction brakets

- RA60 swaybar with SuperPro link and D bushes

- R32 gtr rear rotors and calipers

Interior

Custom aluminium dash,

Speco gauges- Oil temp,oil press,water temp,Tacho,speedo,Fuel,

Gktech steering wheel

Pull type hydro handbrake-Custom extended handle

Snap-ON Shifter

Bride Style Fixed back seats

ERG 5 point harness’s

Azcustom Cams approved rollcage

Exterior

Custom 30mm widened front Guards

back doors welded shut, all flush

Flared rear gaurds

Bonnet cut out to allow ITBs to stick out in the fresh air

Currently Painted Falken Racing team colours- Obviously you would want to change this (can possibly be done for new buyer)

Wheels

17x8 front

17x8.5 rear. Comes with 2 sets

BBS style wheels

fitted with falken tyres... DERRRR

All engine work carried out by Tasmanian Engine Reconditioning

Custom Fabrication Completed by AZcustom

Powder coating by Hi octane Coatings

PIctures and videos,

Now a simple google and youtube search will result in literally hundreds of pics and vids so feel free to do some looking around,

Some of the better ones included below

PRICE

Currently chasing $22K ONO With A1 Bodywork , as mentioned can be resprayed in any desired colour, Aus and possibly world wide shipping available,

[Black.Magic]

Sweet car! Wish I had the dosh!