Jump to content
SAU Community

Recommended Posts

Hi,

I've got this problem with my headlights cutting off when i stop at lights with my foot on the brake.

When I come to a complete stop at the lights with my foot on the brake. my headlights cut off usually they turn back on when I take off again or I just turn them off and on they work. They work fine when driving just when you stop they cut out,

Any ideas

Thanks

Link to comment
https://www.sau.com.au/forums/topic/389339-headlight-problem/
Share on other sites

O.K sounds a bit like you have a short going on. Sounds like your headlight wire and brake wire are touching somewhere and when you put your foot on the brakes the power going to the headlights finds an easier path of resistance and takes the brake circuit.

Is it a case of every single time the headlights go out it coincides with the brakes being pressed or does it happen at any other time?

if so you might need to check the voltage at your brakes with the headlights off then get someone to turn them on and see if the voltage changes at all.

You really just need to check as much as you can. The short idea is just a guess, Hard to say without looking

Hi

Do any other lights come up on the dash? Like a battery light perhaps!

If so it could indicate a faulty voltage regulator/alternator. It could be cutting out @ idle because there isnt enough voltage to sustain the lights. Try putting a multimeter on the output of the alternator with and without the brakes on @ idle and at higher revs. A good voltage output would be around the high 13v to low 14v mark.

Something else to consider.

Hope this helps.

Sorry for the late reply.

You should be careful when poking around running alternators if you not familiar with this sort of thing. There is usually a thick wire which is bolted onto the back of the alternator, this is the output wire which supplies power to the battery and other electrics on the car amongst other things. You can get a positve reading from here, earth lead to a earth like a strut tower nut etc and you'll get a reading. Failing that you can get a rougher idea by putting the multimeter directly onto the battery, but this isnt as accurate.

If your still in doubt, best to consult an auto elec to check it for you. Good luck.

  • 9 months later...

I still have this problem (Never fixed it)

Can anyone recommend a good auto electrician on the gold coast,

Maybe someone good with jap cars or just someone that wont make it worse lol

I've noticed that idle will drop when turning on headlights it doesn't stall, Right headlight dies first then Left or only Right headlight will cutout Left will stay on only after I've stopped I see it in the reflection on cars infront.

Anyway if anyone can recommend an auto electrician it would be great

Edited by dyl33

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • have no doubt and wanted too trust me and may regret later not necessarily worried about weight (would be 8 kg ish total) it was more the $$ to do it properly is about $6 - $7K in hardwear need long 310mm stroke jacks etc - plus install and call me whatever im not doing it myself even if wanted too cant weld etc  - thats $10K installed vs fraction of that cost while Ive spent some money on this POS I actually really dont like doing so unless its got a large chance to make me go faster 😁 hey in still carting this things around on a 15 yr old rusted open trailer so I can spend on racing not buy a new trailer to look better the manual jacks Ive had done are heavy and take space but are transportable and usable anywhere - taking or organizing even compressed air let alone nitrogen which is more whats needed coming from Perth to Winton or Sydney or the like honestly just adds to my brain headaches/ hurts of organisation also ha 15 mins job will get down to 2 - 5 min job vs 1 min job for airjacks - all tradeoffs I spose
    • Purely out of curiosity, how do you know all this @dbm7? Do you work with automatic gearboxes professionally? This goes way way way beyond "I've had an automatic Skyline once and did some mucking around"
    • I'll just reiterate that it's best to do all the wiring diagnostics, before even thinking about buying replacement solenoids ~ that is, be absolutely sure the solenoid is bad.....ie; bad connector(s), rodents chewed through a wire, etc etc. If you don't so this, you can fork out all the money for solenoids, only to find something else is wrong (this'll make you cry if you pull the valvebody only to find a broken wire is at fault... ...some more glue on the solenoid packs -- this is the RE5R01A shift solenoid assembly.... ...these are all shift solenoids ~ ostensibly they're the same as the shift solenoids from the 4-speed auto.... ...this is the RE4R01A solenoid set... ...with these, you have 3 shift solenoids attached to the plate, and the separate solenoid is the EPC solenoid (line pressure control) -- with both designs, the TC lockup clutch solenoid (also PWM so they could slide the clutch shut), is located on the lower valvebody half.... ...(story time)...back in the 90's, it was a common fault that the EPC solenoid (or TC-lock solenoid) would fail, but Nissan only sold them as part of the assembly (think ~$350 at the time) ~ thing was, Isuzu also used these boxes in light commercials, and you could buy the PWM solenoid as a separate part, so it was possible to buy/use that solenoid (around $65), and make it fit (remove the circlip, fit to old plate and deal with wiring)...making it a more cost effective repair. I've not seen the RE5R01A shift solenoid assembly, but with the 4-speed RE4R01A it was possible to hack/fit a single shift solenoid onto an other working set, using a donor solenoid from another set with failed EPC....(by rights the whole set should be replaced), but it ends up being a question of how much life is left in the box itself ; sometimes it's a viable repair to fix one solenoid, just to get another 100k of road miles out of it before it needs first overhaul...other times the box is that old/worn, you're as well doing first overhaul and replacing the solenoids and starting fresh... What Nissan did here with the 5-speed, was relocate the EPC solenoid to the lower valvebody (next to the TC lockup solenoid), and stuck the direct-drive clutch solenoid (for the extra gear) where the EPC solenoid used to be on the 4-speed....I can only imagine they did this for serviceability ; the PWM solenoids are most likely to fail, and it's a doddle to drop the pan and change these out (as opposed to dropping the valvebody itself to get at a top mounted EPC)... ...also keep in mind, that some BMW 3/5 series & Mazda (and maybe some Ford/Mazda rebadges, not sure), also used the RE5R01A box under a different name/part number...not saying parts availability is any better, but sometimes it helps to know this when it comes to NOS floating about in the EU.... HTH  
    • FWIW, air jacks are actually pretty light and simple to add, they are just 4 hydraulic cylinders (often at the main cage A and C pillar points) and an externally accessible airline  - they make quick work a breeze
    • Maximum Attack has entered the chat
×
×
  • Create New...