Jump to content
SAU Community

Recommended Posts

Hi, I'm just after some opinions on my setup. Firstly it's a rb25 series 1

Fmic cooler

1000cc injectors

Splitfires

Too feed fuel rail

Forward facing plenum

Bosch 044 fuel pump

6 boost manifold

And turbo is a gt3582 with a tial 38 wastegate

Now on another page I had numerous guys telling me when I go to get it tuned il be looking at about 370hp max at the wheels , does this sound correct ?? I would of thought Abit hire then that, also at what joist should I get my tuner to aim for ?? Just thought 370 hp was pretty low considering, any responses would be appreciated. Thanks Ryan

Naturally depending on boost, fuel, and dyno - I would EXPECT it to be pretty safely achieveable. To be fair with that combo of mods I'd expect over 300kw on anything over 18psi on pretty much any dyno I know of so long as it isn't weasel piss fuel or there isn't something wrong somewhere.

  • 2 weeks later...

Mods:s2 rb25det 248xxxks hks25/30 z32 mad ,nismo 550 injectors ,hks fmic , walbro 600hp fuel pump ,bigger fuel lines,apexi power fc

Power:239kw@9psi(didn't bother going higher as its my daily)really safe tune.

Oil:mogul

Usage:daily/weekend hacker yet to see a track or strip

Lifespan:4years still performing well

Failures:coil packs and afm changed them to sliptfire an z32

comments:lets see if I can make it to 300000ks ;)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • This piece is obscenely discontinued. I honestly hate the frameless window design because the rubber gets stressed and the guides as well every time you open and close the door.
    • I wouldn't be concerned at all, other than to suggest having them flow tested when you receive them to confirm they are reasonably similar, and then put the highest to lowest flowing ones in cylinder 6,1,5,2,4,3
    • I’m only posting this cause I thought I had seen a bad review on these somewhere before. Any feedback? Would you guys recommend that if I do buy these I send em to RC to have em checked before installing. Or any other suggestions?   https://www.ebay.com/itm/114009965865?mkcid=16&mkevt=1&mkrid=711-127632-2357-0&ssspo=JDl-15yLQ8C&sssrc=4429486&ssuid=QTzlFXB1S-S&var=&widget_ver=artemis&media=COPY
    • They see me rollin' they hatin'....... Took me most of the day to make the necessary mods to the mounts to make them fit the car.  Fortunately I was able to just use the mounts that came with the rotisserie. The rear ones are really secure, the front I feel i might reinforce a bit more as it doesn't seem like enough attachment to the vehicle. I'm sure it's fine but better to be safe than (extremely...) sorry.  I drilled and tapped thread into additional M12 holes to each car mount where it attaches to the rotisserie as an extra fail-safe. Without them the side to side movement is just restricted by the allen head pinch bolts, nothing actually goes though the beam. Does now! I still need to adjust the rotisserie to get the car centred in terms of centre of gravity. If it's too high or too low relative to the rotational centre line of the car, it will be like a turtle and roll onto its back or as it currently sits, I dont think I'd be able to rotate it as it sits as it needs to lift the whole car up as it rotates. Ain't happening... I'm going to be nervous as hell the first time I go to spin it on its side...    
×
×
  • Create New...