Jump to content
SAU Community

Recommended Posts

hi guys, planning my first run down the strip this wednesday at WSID.

my question is about how much fuel to run with. there's a fair bit of difference between a full tank and half a tank of fuel as far as weight goes (perhaps 20kg?). im thinking that having less fuel will help my TS, but then again on the street a full tank of fuel helps get off the line. I hear the strip is much sticker, but how much? If i launch at 3grand on the street, how much more can i add at the strip? -so far all ive done is take the 2x12in subs out, which together weigh about 25kg inc boxes.

note im running on 19in street tyres.

thanks all.

Half a tank will be fine. You don't want too little or it could get bad, quick...

Remember, if you intend to run on the 19's, let some pressure out of them before you run.. Try about 20psi LESS than what you usually run.

So a search for a beginners guide to drag racing on this forum and see how ya go. Better get there early this Wed as there's only gonna be about 80 cars aloud to run due to the burnout comp.

Good Luck!

Adrian

a drag section! funny i never noticed it, only ever seem to be in general or forced section.

yes tits i dont plan on running with a full bowel. That will save a couple of kilos :(

ive asked about tyre pressure for 19's in another thread but i cant find it, and cant remember what the conclusion was, but can anyone tell me from "first hand" experience if dropping pressures in very low profile 19inch tyres will actually make a difference? I think that even if you drop pressure, there is still hardly any sidewall to flex to get benefit from? not that it could hurt so im likely going to drop them anyway.

Adrian, ive never been to one of these burnout comp/street meets, how early would i have to rock up? gates open at 3 i think, i was gonna try to get there by 1? and is it worth going to race while they are having a burnout comp on the same day?

thanks

I dont think I'd worry too much about the amount of fuel you've got (performance wise). I usually need 2 passengers in my car before I notice a significant drop in performance. Last time I went to the track I used 1/4 tank to drive 4 miles!! Make sure you have enough :uh-huh:

Altho I've only ever run on 16" tyres, letting then down is certainly the way to go.

Launching is up to you and how much power you can feed to the tyres without them spinning. There is no "rule" as to what rpm you should launch at, just remember that high revs = good revs. Your mission is to find the point between 2500-6500 where the wheels dont spin, then feed it more.

Let us know how you go :(

To begin with I was removing everything lose except me and the seats... sub, glovebox stuff, center console stuff, jack, spare tyre etc and I was running on about 10-20L of fuel.

Now I leave it all in and use 20-30L of fuel so probably about 25-35kg difference (half a passenger).

The difference I have noticed is no axle tramp with the extra weight in the back (tyres and tyre pressure have stayed the same).

Next time im out on the track I hope to have:

* Semi-slicks

* A clutch that releases and engages gears :D

* Brakes that work :Oops:

If all goes well I might start removing the tyre/jack/sub.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hey, guys, I’m hoping I can find answer here. I have already done some searching and asking around but still nothing.    I fitted an IC7 dash in my R32 GTR, and I got everything displaying on the dash except my high beams. I get input voltage and the high beams displaying in the dash when I pull the lever, but not when I fully engage the high beams. I spliced into the Red/Blue Beam+ wire in the black center connector from the cluster, but there is also a black Beam wire I think I need to use as well. The high beams still work. It’s just a matter of getting it to display on the dash.    Has anyone fully wired in their IC7 properly ? I would appreciate any guidance on this.    IMG_8835.mov    
    • I buy my wheel cleaner in 4 litre bottles now. Euro brakes are brutal
    • Sounds like it may all just be some baseless outrage stoked by the carexplore guy? As in the linked social media outrage on facebook just goes back to carexplore as a source again. Further shown by the council response that nothing actually has changed: "The Private Land Use Permit has been part of the Casey Community Local Law for a number of years. It's important to clarify that this permit is not new, and no changes have been made to the permit or the Local Law in relation to the permit." The full council response in Prank's link sounds reasonable to me. Saying that as someone who neither lives there nor has a front yard to call their own  
    • Clutch hydraulics are also all good, looks like a brand new slave cylinder and everything bled up well. No idea what the actual clutch is, and I don't intend to pull the box off on the floor to find out, so unless we have trouble on the dyno or at shakedown that will remain a mystery for the new owner
    • Front brakes are G4 8 pot calipers over 330mm discs with braided lines. Everything looks good, pretty sure these are off my old 350. Pads are brand new and judging from gold colour are Winmax which is what I also run on my race car, Neil and I both sourced brake stuff from Matty at Racebrakes Sydney who really knows his stuff Everything has bled up nicely with all new Motul RBF600 fluid, there were 2 loose hard line connections and the calipers were new on the car so I ended up doing it 3 times but it is perfect now
×
×
  • Create New...