Jump to content
SAU Community

Recommended Posts

hi

i was wondering if someone could send me in the right direction, i took my car to a track day and it was over heating according to my defi gauges, oil hit 125 degrees and water 105 degrees.

i dont think thats very good for the engine . ive been looking into getting a new alloy radiator and a oil cooler so i can enjoy my track days without over heating.

but unsure if i need twin or triple core radiator as ive been told sometimes to big is no good.

and with the oil cooler not sure how many rows are necessarily needed.

atm my car 98 r34 gt-t has a turn flow blitz intercooler , 3inch exhaust , manual boost controller nothing else mechanical done.

hope u can help me.

Link to comment
https://www.sau.com.au/forums/topic/390170-over-heating/
Share on other sites

Those temperatures are just OK. As in, you can run it that hot but you really don't want it to get much hotter, and you'd prefer it to be cooler. A new triple core radiator will definitely cool better than an old single core, so that will probably help. If you look after the water cooling, then you won't need the oil cooler to be too big. Something that fits behind the brake duct is usually good enough unless you have a monster engine. But before spending money on all this stuff, it might be worth wondering if you just need a new water pump (might have lost some vane to corrosion), or might be better off looking at making sure your air flow through the radiator area only goes through the rad, not around it, etc etc. cheers

Link to comment
https://www.sau.com.au/forums/topic/390170-over-heating/#findComment-6214214
Share on other sites

id say an oil cooler would be essential for track days... there is another thread going about oil coolers / thermostats etc..... Ive never tracked my 33 (i have an oil cooler and relocated oil filter) i barely see temps above 70 degrees.. even after long drives in 30 degree heat with 80% + humidity...

an oil cooler is pretty simple to put in - maybe consider it next time you do any oil change..

Edited by defari
Link to comment
https://www.sau.com.au/forums/topic/390170-over-heating/#findComment-6214230
Share on other sites

I reckon just do the usually checks before u go buyin any expensive aftermarket parts

1 check thermostate operation

2 flush entire system

3 change coolant

4 bleed the system and get all the air out of it

This will pretty much only cost u ur time

then go for your water pump/radiators etc

Link to comment
https://www.sau.com.au/forums/topic/390170-over-heating/#findComment-6214301
Share on other sites

suggest that a vented bonnet might help get the hot air out, do you have a mate you could borrow one off and test on the track?

nope dontno any1 with one. maybe do the track without a bonnet ?

Those temperatures are just OK. As in, you can run it that hot but you really don't want it to get much hotter, and you'd prefer it to be cooler. A new triple core radiator will definitely cool better than an old single core, so that will probably help. If you look after the water cooling, then you won't need the oil cooler to be too big. Something that fits behind the brake duct is usually good enough unless you have a monster engine. But before spending money on all this stuff, it might be worth wondering if you just need a new water pump (might have lost some vane to corrosion), or might be better off looking at making sure your air flow through the radiator area only goes through the rad, not around it, etc etc. cheers

i got my water pump changed 20,000kms ago should be ok i guess ... but i do have cheap kmart coolant in it tho lol so that could be an issue i guess ..

any reason why you suggest triple core radiator ?

id say an oil cooler would be essential for track days... there is another thread going about oil coolers / thermostats etc..... Ive never tracked my 33 (i have an oil cooler and relocated oil filter) i barely see temps above 70 degrees.. even after long drives in 30 degree heat with 80% + humidity...

an oil cooler is pretty simple to put in - maybe consider it next time you do any oil change..

ah just got the car serviced ... yea ive been told they are basicly necessary for track use. just general driving get my car up to about 80-90 degrees oil temp.

Koyo radiator plus anything like a 19 row oil cooler will solve all your problems.

would you recommend cooling pro ? or go with a better brand like koyo n blitz.. wouldnt happen to know if twin or triple core works better with the stock water pump ?

Link to comment
https://www.sau.com.au/forums/topic/390170-over-heating/#findComment-6214318
Share on other sites

I reckon just do the usually checks before u go buyin any expensive aftermarket parts

1 check thermostate operation

2 flush entire system

3 change coolant

4 bleed the system and get all the air out of it

This will pretty much only cost u ur time

then go for your water pump/radiators etc

This is good advice, do the easy stuff first.

Considering you have few mods, I wouldn't blame the radiator straight away.

Link to comment
https://www.sau.com.au/forums/topic/390170-over-heating/#findComment-6214327
Share on other sites

any reason why you suggest triple core radiator ?

Only because the China spec aluminium rad I put in years ago was triple core, cheap and works perfectly. It was clear that it provided much much more cooling than the original rad (the only problem of the original rad was a cracked end tank, the core was in good condition).

Cheap coolant doesn't make any difference to cooling performance. Only to how gracefully the coolant ages (old coolant becomes more and more acidic with time) and hence how well it control corrosion.

Link to comment
https://www.sau.com.au/forums/topic/390170-over-heating/#findComment-6214330
Share on other sites

I reckon just do the usually checks before u go buyin any expensive aftermarket parts

1 check thermostate operation

2 flush entire system

3 change coolant

4 bleed the system and get all the air out of it

This will pretty much only cost u ur time

then go for your water pump/radiators etc

i had an issue when i took my car to a mechanic that told me they specialized in skylines after they done my timing belt they didnt bleed the coolant through and i wasnt running on much coolant at all took it back the next day n they tryed to tell me my radiator was leaking then finaly told me they stuffed up after 4hrs of waiting around.

ill look into that they might have cut more corners fixing it up

Link to comment
https://www.sau.com.au/forums/topic/390170-over-heating/#findComment-6214331
Share on other sites

Only because the China spec aluminium rad I put in years ago was triple core, cheap and works perfectly. It was clear that it provided much much more cooling than the original rad (the only problem of the original rad was a cracked end tank, the core was in good condition).

Cheap coolant doesn't make any difference to cooling performance. Only to how gracefully the coolant ages (old coolant becomes more and more acidic with time) and hence how well it control corrosion.

ohk, didnt no that about coolant lol just last longer the better it is

Link to comment
https://www.sau.com.au/forums/topic/390170-over-heating/#findComment-6214340
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I can't agree. If we hadn't all been brought up with the noise caused by the inefficiency of an ICE, no-one would actually ask for all that. An EV is like any other car, it just goes better. 
    • 2 more things I have to work out Easy one first...can anyone describe how to pull the fuel pump and sender from a 33? I can feel there is some sort of mount and clips but don't have a manual and don't know the trick......if not I'll spend some quality time in the boot witha lighter tomorrow. Second question is harder.  He had changed the upper plenum to a plazmaman but clearly got to a point with the vacuum hoses where he said "f**k it, I'm going inside for a beer" and never came back to that job because it was a mess. Am I right to think that I need: 1. Pre throttle (16mm nipple on inlet) to AAC's main 20mm fitting as the main pre throttle feed 2. ACC has a second 13m outlet joined to that 20mm fitting which I think is the pre throttle air supply for the cold start valve? 3. Cold start valve's outlet fitting then goes to Plenum (to bypass throttle?) There is some adapter on the back of the ACC with 2 fittings (13mm and 10mm), do I run the 10mm through a 1 way valve to the Brake Booster (4) and the 13mm back to a 13mm nipple on the Plenum as the Idle control (5)? 6. Run a 6mm vacuum line from the Turbosmart BOV to the Plenum? 7. Run a 5mm vacuum line from the Fuel Pressure Reg to the Plenum? 8. Run a 5mm vacuum line from the Turbosmart Boost controller to the Plenum? (Wastegate already has a pre turbo pressure source running to the solenoid then the wastegate on the other side of the bay)  Any help appreciated, the GTR is quite different setup and while the Stagea also has FFP it is different again. (And no Dose, I'm not pissing it all off and putting a ethrottle on it....)
    • OK, onto some questions to try and speed up the process a little. Does anyone know what core this Garret is? I know it is a high flowed standard turbo but nothing else about it. Tag says OK 0169J - 446179-5032 Same question for the injectors, I don't know what they flow and ideally can work it out before it hits the dyno, they are a mustard yellow side feed
    • Quick side trip into the engine externals, alternator and PS were in place including tensioned belts, but the PS was dry (my guess is he had the steering rack reco-ed). Filled it up with Transmax Z but it will need more bleeding once the engine is running no doubt. BTW I've said before, I don't know what kind of soft animals you have in the city, but out here they breed the rats tough. I bet they were disappointed when they tasted synthetic ATF.... Coilpacks are Splitfires with a factory loom in reasonable condition. I didn't pull one put I bet the spark plugs are new as its a new engine
    • Onto intake pressure test. I have a Raceworks (damn brand thieves!) pressure test adapter that lets you apply pressure through a standard tyre valve and comes with a pressure gauge.....I just blocked off the other end immediately before the throttle body. Applied 30psi....and the turbo intake immediately popped off with a bang. Sorted that but it was still leaking, turns out there is a pinhole leak at the BOV adapter that I'll have to find a local place to TIG up. I'm sure it makes SFA difference with such a small leak but I want it to be right. Everything else up to the throttle body was good. Also cleaned and oiled the KNX cone filter, and this is the AFM if anyone can identify it (car runs a PowerFC)
×
×
  • Create New...