Jump to content
SAU Community

Recommended Posts

Can somebody tell me why 32 Gtst coupes are still selling for around $8k in stock form? These cars have dings, bad paint, old old engines and they're twenty friggin years old!

20

Years

Old

wHY?????

Can somebody tell me why 32 Gtst coupes are still selling for around $8k in stock form? These cars have dings, bad paint, old old engines and they're twenty friggin years old!

20

Years

Old

wHY?????

because they are still worth it in peoples eyes? as long as people are willing to pay 8k then hats what they are worth

when it so happens no one will pay 8k thats when the price drops down

I'm not debating whether the 32s are worthwhile cars. Rather, I'm frustrated that they're still so expensive, considering you can buy a 33 for $4000 in the same condition, and that I bought my 34 GT-T for $12,000 even. It must be said that my 34 needed a new dump/engine pipe and coilpacks, and potentially a new front bar, but still. You see 32s being advertised for well over $12k, with potentially demonic and unreliable modifications.

Anyway as you can probably tell, I'm possibly maybe in the market for a 32, and I'm a staggered that people want 2/3 the price that I paid for my 34, for a car two generations earlier, in stock condition.

Ah well, such is life.

I'm not debating whether the 32s are worthwhile cars. Rather, I'm frustrated that they're still so expensive, considering you can buy a 33 for $4000 in the same condition, and that I bought my 34 GT-T for $12,000 even. It must be said that my 34 needed a new dump/engine pipe and coilpacks, and potentially a new front bar, but still. You see 32s being advertised for well over $12k, with potentially demonic and unreliable modifications.

Anyway as you can probably tell, I'm possibly maybe in the market for a 32, and I'm a staggered that people want 2/3 the price that I paid for my 34, for a car two generations earlier, in stock condition.

Ah well, such is life.

good story bro

As cars get older their decline in value reduces and reaches a break even point, R32s have pretty much hit this being over 20 years old now, even R33s will be hitting this point soon. The fact is R33's can be over 15 years old now so it is at the point where a well looked after R32 is just as likely to be reliable as an R33. R32s tend to be more 'enthusiast' oriented as well, and from what I can see are usually less showy and more to the point, probably a lot more suited to the track/weekend car market than a R33/R34 is. In a lot of peoples eyes they are a lot more desirable.

I'm biased because I have an R32 for sale for $8000, but it is quite well modified, and I would assume much more reliable than any $4000 R33, and a much better basis for a track car. I've rationalised this by looking at the market and then adding about a 1/3 of the cost of all the modifications I have done(since they have all been done recently). I currently have someone waiting on money to buy mine because they want a good street/track car, I've had other people come check it out and not be interested because of usual old car problems such a few scratches and paint chips and expectations that you would have for a normal car that just aren't realistic and should probably just go buy an R33/34 if they are worried about that stuff.

Edited by Kwyjibo
  • 2 weeks later...

Fair enough, you make some good points.

I sure do like the R32, because it's a nice and handsome shape, handles well, is the lightest of the lot, and it's fairly cheap and a raw experience.

I'm just frustrated that I can't really afford one without getting a small loan (something which I've sworn never to do again after having the devilish bank on my back for a year due to my R34 loan)

So anyway, good luck to those selling 32s and good luck to those looking.

laughing-smiley-014.gif

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Good news!!! Changed the O ring today and Iโ€™ve got the โ€œpssshhhhโ€ back when I open the fuel cap ๐Ÿ˜‚๐Ÿ™Œ๐Ÿผ๐Ÿ™Œ๐Ÿผ It was 100% the O ring because that bloody thing was inside the fuel tank ๐Ÿ˜‚๐Ÿ˜‚๐Ÿ˜‚๐Ÿ˜‚๐Ÿ˜‚ Fitting new fuel pump was a pain as always since the DW is a bit longer than stock. But sheโ€™s running!!! โค๏ธ
    • PWM quite literally just chops the ful 12V voltage on and off at whatever duty cycle you're running it at. If you're running it 100%, then it is on full voltage all the time, same as if there was no PWM. If you run it at 50% duty cycle, it is only seeing the full 12V half of the time. This is broadly equivalent to running it at 6V. But the crucial difference is that motors (and a lot of other loads) don't like being powered at low volts. They will either fail to start rotating, or draw a shit ton of current, or other undesirable things. But if you give them the full volt, and then a short period of no volts, and then some more full volts, then the times when they are seeing power they are seeing all the voltage, and they are happy. But you get the performance out of them as if they were only seeing that fraction of the full voltage. It is not really easy to answer your question about what flow you will get out of it at 50% duty cycle. I can tell you that it is not as simple as you think. For a start, that 460 L/h pump is not going to flow 460 when you're on boost. When you're on boost you will be somewhere down the sloping part of that red line. If you have 15 psi of boost, then the pump can only deliver about 95 gal/h, which is <380L/h. So your simple 50% on 460 = 230 wasn't going to work anyway. But also, it won't deliver 50% of 380 either, because when you devolt or PWM trim th epower being fed to the pump, it is not able to deliver flow or pressure in the same way. 50% duty cycle will probably produce <50% of the full voltage flow. The way to find out what duty cycle you need to run it at at low load (ie, at idle) is to idle it and turn the DC down until you start to lose fuel pressure, then turn it back up above that with some extra for safety. And then you do the same thing at full load, in case it doesn't need anywhere near 100% DC. And if you're careful/caution/prudent, you will also do it at a couple of loads in between so you can shape the DC map against load. It might not be linear between the two end points.
    • Man that dinner was such a long time ago....2010! I would only replace the rubber coolant lines with silicone these days; cheap, readily available and will last for ever. You will need new hose clamps though egย https://justjap.com/products/cooling-pro-silicone-engine-heater-hose-set-black-nissan-r32-gtr-rb26dett
    • I wouldn't look too hard at what they did with the R32 GTR in endurance racing in Australia... Lots of things weren't actually available from the factory in the way those cars ran them... Japan also followed what Fred Gibson was doing here with some of there endurance cars in Japan... Australia is also the reason for things like the Brembo brakes, and the change in the gearbox... And quite a few other tricks they used to pull. There's a few other SAU peeps still on these forums that will have heard the stories direct from Alan Heaphy, Fred Gibson, and Jim Richards when we were lucky enough to have a great dinner with them
    • For all the talk of "these parts are junk" I generally recommend OEM because it's really not as bad as claimed. I have never seen or heard of a case like the N63 where the oil returns completely clog with coked oil for example in ~10 years or less. Would it be nice if it were a straighter path? I guess, but most modern cars use a scavenge pump instead of a pure gravity return. Also the factory lines that would be relatively simple to convert to braided are generally speaking hardlines from the factory. I would consider braided line to be a regression, not an improvement. It's also been engineered such that all the hardlines have appropriate strain relief where needed. There's absolutely room for improvement, for example the HKS advantage heritage intake piping shows just how much can be done to make the turbos fight each other less in OEM twin turbo configuration and reduce compressor surge but it's rarely a simple/straightforward process. I recommend looking at what the group A/N1 cars did, generally speaking the changes they made were necessary and proven in endurance racing.
ร—
ร—
  • Create New...