Jump to content
SAU Community

Recommended Posts

18" wheels and anywhere between 225 and 245

18x8" +20 on a 235 tyre

18x9" +30 on a 245 tyre all around is what i run on the front and thats flush to guard no rub no scrub no issues (my car sits slightly higher then most due to my driveway).. so you should have little trouble going that all around (check my photos on previous page)

Hi all,

About to get some wheels tomorrow in the size 9,5j et+26 all around for my R34 GTT with nismo S-tune suspension.

Thread has been great help.

Looking to run 245/35/18 front and 255/35/18 rear. You think I can run this without rolling the fenders or any other guard work?

If not...what size tyre should I run

Cheers from Holland :action-smiley-069:

Edited by ThomasGTT

Hey mate. A 9.5 +26 will have a tiny bit of poke from the guards you may want to run a smaller tyre for clearance issues but you could probably get away with a 245.. my old 18x9.5 +22 had guard rub when going up inclines and full lock that was with lowered coilovers and a 235 tyre.. also worth mentioning make sure you wheels will clear your suspension arms on the front.. mine had a tiny gap between wheel and arm

Cheers good luck

Ps i had unmodified guards.. i would recommend rolling them if your car is lowered with that size wheel and offset

  • 3 weeks later...

18x9+25 would sit a little inside on the rears if anything. Perfect flush fit in my opinion is 18x9+30, even on that it'll sit in a little on the rears but nothing substantial

Edit: it would stick a little out than in, myyy bad

Edited by tiddyd

hey guys, i was thinking of going 18x9 +25 all round, was wondering if it would poke outside the guards considering the front on your ones look pretty flush

18x9+25 would sit a little inside on the rears if anything. Perfect flush fit in my opinion is 18x9+30, even on that it'll sit in a little on the rears but nothing substantial

  • 3 months later...

To revive this thread, this is my R34 gtt with LMGT4's in 18x9+22 front and back.

Wrapped in 235/40/18 re003's all around.

No camber to them, guards are rolled at the front but probably didn't even need to, there's no scrub at all.

Perfect flush fitment front and back.

post-129215-14492702784164_thumb.jpg

post-129215-14492706898209_thumb.jpg

  • 2 months later...

More clear photos for you mate, yeah i noticed a huge improvment when i swapped..any photos of your new wheels?

Hey Artic, what front bar/kit is that? Lip looks great on it! Wheels look great also, glad to see a reference as i'll be running a similar 18x 9 or 8.5 + 30 all round when i finally get mine.

Edited by RR34GTT

Hey Artic, what front bar/kit is that? Lip looks great on it! Wheels look great also, glad to see a reference as i'll be running a similar 18x 9 or 8.5 + 30 all round when i finally get mine.

Cheers bud. Its a ztune replica for gtt :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yuck. But it's kinda the same principle, moving timing around to make car run bad but sound good.... I went for a more spirited tuning drive to iron out a few things. Car no longer stalls, and it loved to dip RPM low when you clutch in. After tuning this (and the 4-5 tables that HPTuners/LS1 OEM ECU wants for idle air correction) it's now behaving somewhat normal. All expected because there's a new TB, new Intake manifold and that new TB which is 102mm vs 78... has an entirely different IAC passage which is smaller because ????? Unfortunately at this point I went to make further fine tuning changes to avoid it flaring up, you know... _tuning_ the HPTuners dongle died. Well to be more accurate - The USB cable died in a fashion that anyone who has ever charged a phone will recognize. After the app demanding I resync it 50 or so times (which all 'succeeded' but all failed) the device does not want to sync and I've logged a ticket with support to see if it's fixable. US Support said it was a 'storage issue' but after removing the SD card inside it and formatting it/fixing it the issue does persist. Unfortunately usually the fix is "Turn in your old dongle and pay $700 for the upgraded one" it's cheaper because I get some free licence credits I unfortunately don't need. However I'm 10 minutes down the road from HP Tuners AUS/VCM so at least I won't need to post it, and logged a new ticket for support over here. Definitely drives different. My SOTP dyno believes it's probably making 310-320kw instead of the 280 before.  It scrambles for traction a little now whereas it previously different. It drives like a bigger cam car up top even though the cam is smaller, likely due to the cam not being advanced 6 degrees. The timing is deliberately low and the fuel is very rich so who knows if this will improve on the dyno. It may, imperceptably. Also funny is removing the pineapples definitely makes the car squat more and axle tramp less. So this behavior of having more top end, squatting more, and scrabbling for traction more makes me think = more power. But I could have just been sitting on the threshold of that kind of behavior before. Time will tell if my butt dyno is calibrated right. I need the exhaust leaks fixed before dyno tune for obvious AFR related reasons - I repositioned the pipes but I'm not confident it's fully sealed even if it is better. At least the car does drive around while I cannot tweak/tune it for now. And I have aircon again. medium success!
    • Don't use that manifold. Please don't use that manifold. Sunk cost fallacy is not worth the later pain. None of these will be relevant to the change that will come from the different turbo and manifold. As in, the effect of the exhaust will be nil, regardless of what else is changed. And all the cam and fuel system stuff is not changing either way, so has no effect. The turbo and manifold (and to a small extent the wastegate)....big change.
    • Just wanted to say thank you for your input   my man (lead mechanic by trade) and I have done a heap of work as you can imagine just to make the hot side work with the dump pipe, stupid massive intake on turbo, trying to get the waste gate on was not fun.  I’m kinda getting to the point where I don’t know if I try and make this work and not throw all this cash and time away or do I scrap the lot and start again? the Apexi I’ve got was tuned for a few slight differences:   Tomei pon cams (mine are stock neo) Turbo smart 38mm external waste gate (mines 45mm replumbed) with stainless screamer pipe  3inch turbo back exhaust with high flow cat Sard 800cc top feed injectors Sard adjustable fuel pressure reg    
    • Out here E90s are the cheapest way into a sporty-ish car because everyone knows just how expensive the repairs can get. 8-10k USD for an automatic 335i. 
×
×
  • Create New...