Jump to content
SAU Community

Recommended Posts

My story is was on freeway, and there was debris on the road, a sheet metal, first big truck in-front of me ran over it and couldn't see it in time to avoid it so i ran over it and my tyre pop , puncture right on the side wall or near it and can not be repaired.

question is can i call vic roads and explain the situation and send them the bill for new tyres because they the one supposed to monitor and keep freeways cleans to prevent this stuff from happening (or who is responsible local council), will it work or they cannot do anything about it?

or i have to get it fixed and no one is to blame :(. so sad because i saved lots of money to get truck licence and this happens :(

Link to comment
https://www.sau.com.au/forums/topic/390662-need-some-vic-road-knowledge/
Share on other sites

goodluck with that, sadly more then likely it came off a truck also,

even if you had a case it would take months and big money to even get to court,

sadly its just one of those things, as it was debris; most likely from a truck, it wasnt a power pole or street light that was on the road.

If every person who ran over material or hit an oil patch was to sue the local council it would cost alot of time and money. ALSO if you got to court they would argue that it was your error of judgement to not avoid the obtrusion.

You will be better off just paying for new tyres and going about your business, I had a bad luck with buying my car, got it cheap but still didnt expect the engine to be sick, so I have had to do a rebuild already after just buying it.

Sadly its just life.

IF you went INTO vic roads and the manager laid into your car with a baseball bat AND you got it on camera AND sent it to ACA/TT.............

they would do a story on "hoon car breaks gov't employee's baseball bat" and you'd probably be hit with a bill for a new bat.

welcome to Victoria

Vicroads can't be held responsible as it more than likely (most definitely) came off the back of a truck, which can happen at any time and they can't monitor this any more than you can. In the event of this, if you see the truck it comes off and take note of their details then you can hold them responsible for the damage, but if it was already there on the road and you simple hit it...yes, bad luck for you :(

Where councils are concerned, is with regard to things they are in control of and responsible for maintaining over the long term, e.g. bad potholes, falling branches from overhanging trees that should have been cut back. Even then, as Hamish said you're likely to cop a bill in the mail for the tar to fix the pothole or a notice from the EPA for taking out a tree branch.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • FWIW the depth of the groove in the rubber pad is not super essential, the blocks are rubber and squish a bit. If you are worried an angle grinder will make a deeper groove quick smart
    • I mean, if you were to move the jacking points away from the original location, that is, away from the wheels and closer to the centreline of the car, then it will be more likely to overbalance and tip off the supports. Same as we talked about before. I was talking about moving for-aft. If the sill is bent outward or inward, then the car would obviously look unstraight from the outside. Hopefully that hasn't happened either. Again, you can do comparative measurements from the chassis rails to see if there is much deflection.
    • Can you elaborate what you mean with your first sentence? I meant move as in the bulge kinda seemed like it got pulled "outward" meaning it got pulled down and to the side with the jacking rail itself, so the load bearing bulge now sits lower than usual and is not level with the sill on the other side of the jack point. Either that or the jacking rail just got pushed in a good bit.
    • As well as being risky WRT tipping off anyway. Yeah, I wouldn't expect it to move. Just measure from the rear one to the front one on the good side, then measure that same length on the wrecked side. You will find the notches in the pinchweld, and the jacking pad. Just spray a spot of marker paint or something there.
    • but any other area than the bulge you are talking about will just cave in then? The front driver side is pretty bent so I don't know if that will work the way it is now. I can still kinda make out where that bulge is/was but it looks like the position of it also changed due to all the mistreatment? Hard to tell
×
×
  • Create New...