Jump to content
SAU Community

Recommended Posts

Ok so i want to know if there is any difference between the Nissan skyline GTR r34 and the R34 gt-t/gt in the raw body size, meaning like if i stripped both of them apart would there be any difference in the size's of the body, or did nissan use the same chassis and just put genuine GTR parts into one chassis please help me thank you

Link to comment
https://www.sau.com.au/forums/topic/391378-some-one-please-help-me-urgent/
Share on other sites

  • Replies 49
  • Created
  • Last Reply

Top Posters In This Topic

I have searched high and low through the whole internet trying to find answers on this, but i still cannot find any answers that i am looking for, some please give me some confirmation on this, thank you

The chassis rails sit in the same position, but the rear and front guards are pumped to fit wider wheels. While the front guards are easily changed over, the rear means that is very difficult to match the track of a GT-R. There are blister kits available but involve making very permanent mods (damage) to a gt-t chassis.

So Would it be possible to strip the whole GT-t and rewire it and fit it with ALL genuine GTR parts onto the gt-t as if it was a GTR ?

yes IF you had a GTS4 in the same chassis. if you are thinking of buying (or have) a GTR34 and dropping all of it into a GTT then the front drive system will hang you. the chassis rails ARE DIFFERENT in the front of the car. there are subtle tweaks in the floor as well.

in my case I have GTR electricals in a GTS4 R32 chassis and IF I wanted to do a FULL swap it would be the entire front end swap AND new inner/outer rear guards as well. swapping the outer panels wont work.

what EXACTLY are you trying to do?

Ok ok I have A Gt-t r34, and i want to strip it completely of EVERYTHING and put all genuine GTR parts into it except for the drive train, leave that at rwd, but everything else make it as GTR as possible

Ok ok I have A Gt-t r34, and i want to strip it completely of EVERYTHING and put all genuine GTR parts into it except for the drive train, leave that at rwd, but everything else make it as GTR as possible

Mate, here's my last piece of advice.

I suggest you start collecting GTR body parts now before you do the conversion. Yes, everything can be translated across with fabrication and custom body work.

Get the shell of a GTR and then transfer it across and you will notice the difference which will require custom work.

It will be a BIG project, so the question is why don't you just save up a bit longer and buy a GTR?

Mate, here's my last piece of advice.

I suggest you start collecting GTR body parts now before you do the conversion. Yes, everything can be translated across with fabrication and custom body work.

Get the shell of a GTR and then transfer it across and you will notice the difference which will require custom work.

It will be a BIG project, so the question is why don't you just save up a bit longer and buy a GTR?

beat me to it.

to put this into perspective - the rear guards are well over $1k each just to get the track/look right.

save your money and buy a GTR. easier. if you are looking for hectic rear skids buy a commodore :P the GTR is 4wd for a reason.

Bro, you're the first person in the whole wide world that prefers a RWD over a AWD but yet want his car to look like A GTR.

Do you want to go all-out or just want GTR bodykit items? Check this: http://www.youtube.com/watch?v=ErMIsPSzxlc

Mate, with $$$ anything is possible.

i wanted to make it look ( exterior) exactly like a GTR in the video i could easly tell that wasnt a true GTR, the front bumper is different, and also, the drivetrain, would it be possible to swap the GT-t one and putting it into a GTR ?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • It was roughly 3.5 hours.    car went in around 11:00 and I was done around 2:30 He did the initial runs, install the BC and then Nistune install and tune.  The best part was sitting in the lobby and hearing the skyline on full throttle at the dyno 😂😂
    • Glad it all went smooth. How long did the tuning process take?
    • Yeah that was kind of the same feedback my tuner gave me.  the boost tee is until I can sort out my plan for the electronic boost controller and what I’d get, where I’d mount the dash etc.  I’m happy with this until I can figure it out. Not a big fan of the A-pillar gauges. I’d like to get a clean install of the boost gauge - something digital like GFB.  Something like that might fit neatly where the ashtray is and look clean. I feel like replacing the OEM triple gauge is a bit extreme for a weekender like my skyline. And it’s not making crazy power to need all the additional sensors/gauges. 
    • I'm about to swap my box to Tremec T56 Magnum F & initially thinking of re-using my DCS twin plate (can get it re centred for the bigger spline) but it's been called out the box will be noisy (rattle) as the clutch is unsprung.  So I'm doing as much research as possible. I'm not so worried about holding the power as I'll go the track version which on paper will hold the maybe 1000hp I make. It's the longevity I worry about. DCS told me they don't use a sprung centre as it's just something that can break. The uni clutch has a very complicated sprung centre. Any one had or heard about any issues with it failing? Thanks in advance.
    • Auto is at least 10% (from my real, actual experience with different torque converters and manual on the same setup) ~185rwkw at 11.6psi (peak!) is entirely what one would expect without a FMIC or anything else on the intake, it does bleed off towards the higher RPM so it's what, 9psi there? Note: There is nothing that can be done about this with a manual boost tee. If you want to hold it steady and gain more top end, well - You will need electronic boost control.....
×
×
  • Create New...