Jump to content
SAU Community

Recommended Posts

thanks for the replies again.

the boost controller is just the manual boost T, the cheap $30 ones.

not sure i get how the boost is working, well specifically why the minimum would be 1 bar? my standard turbo was set to 10psi. now with the hiflow the shop set it electronically to 11 (ok well on the dyno sheet that is where it is making the power). that said, my gauge can be pushed to 14.

Fuel pump is stock also.... my plan was to only upgrade things when and if the break. Hence the turbo.

Thanks again!

:blink:

hmmmm. changed plugs a few years ago... that could be the prob.

I woudnt be waiting for things to break before replacing them, cause the next thing could be your engine, due to leaning out.

upgrade fuel pump.

Stock ECU cant be tuned, so they just turned the boost up, probably just before it went rich&retarded.

I reckon your safest two choices are to turn boost down and read lots of SAU to learn what it is your driving or take it to a respectable mechanic to fix.

buy an aftermarket ECU, if your impressed by a highflow accompanied by all the stock parts, then you'll loose your shite when you get a tuneable ECU and fuel pump.

and yeah which is it, an electronic or manual boost controller???

Edited by 75coupe

thanks for the replies.

As said this came from shop which are a very reputable mob. I don't ever touch any of the car myself and this includes upping or lowering the boost!!

They had it on the dyno and managed the boost, etc through there equipment. They agreed with me that I want it to be as reliable as possible as it is my daily driver.

This was done so that it wouldn't lean out etc.

Don't get me wrong, they seemed quite surprised with the power result of the car (as was I!!!). I wasn't too fussed about power output, just wanted to make sure it was reliable but am really happy with the power it did make!

I spoke to the guys again and they said it would definetly be a faulty coil pack. they were happy with the car with everything else and said given it is so intermittent (sometimes happens at 3500rpm, sometimes 5000rpm and sometimes it doesn't).

Rather than get them to change coilpacks and plugs (quoted at nearly $900!!!) I thought I'd see if I could do some of this myself as funds at the moment are running low!

If it gets any more difficult than plugs or coilpacks then it will go back to the shop!!

thanks

Edited by MAS_R33

Your just hitting Rich and Retard. Search the forums for it. Trying to run anything other than stock on a r33 is just a waste of time, the ECU's absolutely hate it when they see anything their not expecting.

Whats happening is your hitting the limit of how much air the ECU wants to see going through the engine. When it sees this, it pulls all timing until its corrected. Thats why it'll feel like you hit a flat spot in the rev range.

If your running 11psi you could try dropping it to 9 or 10 if your JUST hitting it occasionally, but either just run it stock or get a nistune and avoid all these hassles

ahh ok.. so this would be the case even though it is intermittent?

ie. sometimes i can drive it and nothing happens - even hitting high boost

sometimes it will happen at 3500 (before hitting high boost)

and sometimes it hasppens at high boost.

I would have thought if it was ECU it would be at a consistent spot?

cheers

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Sharing results from recent Liberty Walk R35 GTR, since they are still considered as somesort of a V36 Skyline. We do them turbos too. This are high flowed SS-1 models with ball bearing conversion done.  Car have managed to pull 485awkws @ 20Psi so far pushing limitations of factory built engine. The build list for R35 GTR enthusiasts as follow : HyperGear high flowed stock turbos in SS1 (G25-660 specs) Custom titanium intake pipes. Vspec performance titanium front pipes. Vspec performance 4" titanium exhaust. Upgrade fuel pumps. 1200cc injectors. Ignition coilpacks Hks intake plenum. Hks intercooler piping. Greddy intercooler. Greddy bovs. Top-secret coolant reservoir. Emtron ecu. Straight E85. Built gear box.  
    • Nah no bearings, just slip fit.  Would be a reasonably challenging but not impossible job to modify it to run bearings but I'm hoping that's not necessary as I may have well built one myself if I end up spending hours modifying it!
    • Brumbys with good shells are bloody expensive, I've looked at 2 "cheaper" cars, and walked away from both,  plus after some research spare parts are fairly sparce I'm starting to think that I missed the boat on finding a clean one that is straight (ish) and without alot rust I'm starting to think about a old Hilux as panels and other parts are much more available as they sold tens of thousands of them I use to be indecisive but now I'm not sure
    • A Brumby would probably fit a big metal toolbox in the back... this is how it begins  
    • Picked up a new OEM boot seal for the MX5 today as the old one got ripped a bit by me being a idiot by seeing if I could fit a large metal tool box in it, it didn't fit, and ripped the seal with the corner of the tool box I am still waiting on time to get the cams and new balancer installed, as well as the repairs to the boot Time will not be an issue soon though
×
×
  • Create New...