Jump to content
SAU Community

Understanding 5 Stud Conversion R33 Gts

FLUID
 Share

Recommended Posts

FLUID Enthusiast

FLUID

Posted
Posted

Hey, just need the low down on what i need to do to convert from 4 to 5 stud on a S2 r33 gts, Any links to kits available, Why do i need gts-t brakes for the conversion etc.. Any help is appreciated i just want to understand what i need to do / what parts i need to get and the easiest way? May be able to get some gts-t shocks if that would help at all. thanks

central coast person Proficient

central coast person

Posted
Posted

You dont need the brakes the only reason people change the brakes is because the caliper will clear the rim with a 5 studd providing its got a good offset so the larger caliper can fit. The stock non-turbo brakes are bad.So if you just want to change to a 5 studd rim you can leave your old calipers if you dont want better brakes.

There wont be a difference in suspension between GTS and a GTS-T shock you wont need to touch your suspention when you do the conversion. Not even the knuckle that the suspention attaches to.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • sunsetR33
      ugently need expert / experienced opinion

      By sunsetR33 · Posted

      Just a follow-up on this topic. From what I can tell so far the rusty residue on the engine block might be unrelated to a coolant leak or maybe just older than anticipated. After driving it from the winter garage to my friend's garage I could not see any new traces of coolant leaking there, but I will test this properly once I was able to fully warm up the car and drive it for a bit. I think I can agree that the whole porous engine block stuff is kind of nonsense, but there is just a silly amount of true, false and half-true information on anything Skyline-related on the internet.
    • Butters
      UniClutch

      By Butters · Posted

      hrmmm , not mine , easter plans to pull engine not happening     
    • DRoc81
      R33 GTS25 NA - Stalling when vehicle is at operating temp

      By DRoc81 · Posted

      I removed the IACV, cleaned it and reinstalled.  I found a video on youtube that helped with the whole process, the guy then said the idle needed to be set, so the process was to get the vehicle up to operating temperature, unplug the TPS, set the idle screw in the IACV so the RPMs were around 600, then plug the TPS back in.  After I reinstalled the IACV, the car started (because, it was a cold start), once it warmed up, the car died, I adjusted the idle screw to see if that helped anything, it did not, I had to wait about 3-5 minutes, then the car would start back up. Only to shortly cut out, and only crank.  I loosened the TPS to see if adjusting that would do anything, and when I would rotate the sensor clockwise, there was a humming noise, but it would go away when I got the sensor in the horizontal position.  It only made the hum noise with the key on.  What do you guys think? 20250414_172604.mp4
    • Milkmun
      Magnetic Drain Plug Snapped in Half

      By Milkmun · Posted

      At least it was the ex.
    • Murray_Calavera
      Troubleshooting - motor wont turn over

      By Murray_Calavera · Posted

      Quick update.  The engine grounding strap was replaced, the engine is now happily running.  Tested the voltage drop before replacing the strap, was about 1.2ish volts down between engine to battery, chassis to battery. With the new grounding strap, pretty much no voltage drop at all. 
×
×
  • Create New...