Jump to content
SAU Community

Aftermarket Headlights

Jayce23

By Jayce23,
in V Series (V35, V36, V37 & Infiniti)

 Share

Recommended Posts

pv35gt8 Collaborator

pv35gt8

Posted
Posted

You wont be able to use they factory HID setup on the sedan lights, there is no mount or hole for the factory setup.

There is just a rubber cap over the back of the globes, which is the only access for the wiring.

You will require an after market set of HID for this to be possible.

  • Replies 478
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Posted Images

GSX RRRRR Contributor

GSX RRRRR

Posted
Posted

Easy partner!!! I believe once all has paid he then has to go on the yahoo auction thingy and once he has the headlights he then will contact us for the shipping. From there depending on the type of shipping requested you will have them within 5 days. He did mention of some public holidays over ther in japan, maybe thats the hold up?

Although it has been a while!!!!!

pv35gt8 Collaborator

pv35gt8

Posted
Posted

With regards to Jesse purchasing the lights he would be going directly to the supplier.

I regards to the HID setup for the sedan lights, you will not be able to reuse the original setup. Go and buy an aftermarket set of H7 HID's, when you get the new headlights, remove the two wires going into the low beam section and cut them. Now solder these two wires to the power input on the aftermarket HID kit.

The series one sedan factory HID setup is in two parts, the ballast under the headlamp and the igniter module inside the headlight (which requires dismantling of the headlight to get to it). The series 2 sedan and all of the coupe's these two components were combined into the one unit under the headlight.

Kolossus Proficient

Kolossus

Posted
Posted

So retain the factory harness ditch the factory ballast with the factory lights, (do the new ones have halogens in them already?) And replace with aftermarket hid's, that's cool I get em cheap as threw work.

pv35gt8 Collaborator

pv35gt8

Posted
Posted

The new lights will come with a harness already attatched, when you unplug and remove your original headlight the harness stays with it you wont require anything off it. You will be splicing into the new harness on the new light.

manc01 Collaborator

manc01

Posted
Posted

Nice to see that there are 4 units paid for in full with shipping. I was wondering if anyone has anymore pictures of these lights that they could post on here? Excitement will build even more then while looking at what we are getting soon!!!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • TurboTapin
      R32 GTST - 600KW+ RB28/CD009 Build

      By TurboTapin · Posted

      I picked up my block and head last week and have been slowly assembling it since then. Pictures I took earlier this week. The rest of the auxiliaries are on now. I just have my intake manifold runners to tap for my WMI direct port setup before putting it back on. I should hopefully have the motor back in by this weekend.   
    • TurboTapin
      New fix for low tyre pressure from bmw

      By TurboTapin · Posted

      I couldn't agree more. As an owner of a built high HP skyline, I'd be a hypocrite to not buy a Hummer for the reasons you listed though haha. 
    • PranK
      Hiya!

      By PranK · Posted

      Hahaha oh shit! Again!
    • soviet_merlin
      Stagea boot lid probs

      By soviet_merlin · Posted

      Is this the one? https://jpjdm.com/shop/index.php?id_product=2192&rewrite=nissan-stagea-c34-rear-boot-actuator-assembly-90550-0v000 Might be worth having a look at yahoo japan as well. Though it seems a bit odd. If the motor works itself, other than being noisy, then wouldn't it be more likely that it's an electrical issue somewhere else? And it being noisy does not seem as surprising if it has been chugging away for months  
    • BCs300z
      Stagea boot lid probs

      By BCs300z · Posted

      I know this thread is quite old, but I found it, it helped me, but I also wanted to add my experience and troubleshooting finds to the chat for others. I have not been able to open the rear hatch of my 97 Stagea for several months. Figured it had just really sealed itself up over the winter and I would just get to it eventually. Well that day was yesterday. Some time ago, I noticed my battery was going flat all the time. It was frustrating. Then one quiet night in the garage, I could hear and ever so slight humming / grinding noise coming from the back of the car. It was like a really quiet popping sound or something like sand in a very low speed blender. I took off the panels in the back and noticed the noise coming from the auto close motor, so I unplugged it and the noise stopped. And the auto close was disabled. Well, fast forward to yesterday, I tried all the tricks with power and fuse and lock and unlock and I still could open the damn hatch. So I took off the panels from the inside and found the auto lock had engaged and was stuck in close position. When plugging and unplugging the fuse, I could hear the relay clicking. So I plugged the autoclose motor back in, and the damn thing let go. And immediately started making that grinding sound again. This time, instead of just unplugging the motor, I pulled the fuse, thus depowering the relay entirely. I don't have the autoclose feature now, but at least I can open the boot and not have my battery being sucked dead all the time. Not sure what caused the motor to latch when it was unplugged from the system, but I am pretty sure it won't cause any more problems now.  If anyone has a lead on a new motor, please let me know. It's a cool feature that I would like to get back.  Hope this helps.
×
×
  • Create New...