Jump to content
SAU Community

How Do You Launch Your Gtr?


w34ponGT
 Share

Recommended Posts

All it does is let any little slackness close and let the whole drivetrain lean on the clutch so when you pop it you don't have the little tollerences bang closed. The clutch won't do anything harmfull in comparison to the actual clutch drop

Link to comment
Share on other sites

can someone please explain side stepping?

i got a 1.89 60ft by dropping the clutch at 7k with wheel spin all of first on the limiter lol. ran a 12.1

got 315 rwkw with 255/35/18 profile tyre. kept pressure at 36 because it was still bogging down at 6500 rpm .

with my setup how would use do it?

What brand tyres where they cheapies or actual quality?

Reason i ask is my mate cracked a 12.3 on a 34R with nothing but 1.2bar boost on the stock ceramics and a full exhaust with Bridgestone RE01's (still running std injectors, fuel pump, ecu). It was only about 255awkw from memory too.

Link to comment
Share on other sites

  • 1 month later...
  • 1 month later...

www.youtube.com/watch?v=l_eR-39CK9Y&sns=em

Hey Xklaba u remember me beating u a few years ago in my old GTR?

Man i suck at Embedding vids with my phone. Have to copy to address bar

yeah I remember, and that smoke was number 2 piston going bye bye, I had run 11.36 before that and I have sence run 11.13 with only 293rwkw and stock turbos :P

hand brake is the best way IF you have a good clutch, other wise no hand brake dial in 7000-7500 and just find friction piont then ride out works for me

second gear launchs in standed ratio 34 or 32 and 33 with 4.33 diff ratios other wise use first and short shift to second

Link to comment
Share on other sites

  • 2 months later...

^^ how i launched afew weeks back, although only took it to 6800rpm to launch, finding the friction point then riding out gets best traction and 60ft times too

gonna try 7000-7500rpm next time and see what difference it makes

what sort of tyre pressures did you run XKLABA ?

Link to comment
Share on other sites

street tyres ( 265/35/18) I run 30 psi, you need the pressure to keep the centre of the tyre flat on the ground with even pressure across the tread and since the side walls of low profile tyres don't twist/flex there is no advantage to lowering the pressures, all it does is make the side walls take the weight and reduce the grip in the middle of the tyre

Drag tyres, ( 255/50/16 Toyo TQs ) 18-20psi, opposite of the street tyre reasoning

Link to comment
Share on other sites

bahaha, standard ratio R33 GTR, use first and short shift into second, even with stock turbos that get 19psi by 2800rpm it's hard to keep it on boost on a second gear launch, so much so I don't even try it anymore and I reeeaaally hate clutchs

Link to comment
Share on other sites

best last night for me was 11.3sec again, but this time with a 127.5mph....7500rpm clutch slip seemed to work good and not bog down....traction was abit of an issue though :/

going drags is getting addictive

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share




  • Similar Content

  • Latest Posts

    • There is a LOT of stuff that can be done, it all depends on how much time and money you want to spend on doing in.  Not all ECUs will be able to do it, and the more control you need the more time and knowledge needs to be put into making it work.  If you're willing to spend the time and money and have the right hardware and skills involved there's a lot that can be done. 
    • I am impressed with all this level of adjustment. I didn't expect all this possibility
    • Correct.  In the case of the 500kw dyno plot I showed you the car actually runs two boost control solenoids for boost control and a 5psi wastegate spring.  It allows me to control how much boost pressure is applied to both sides of the wastegate valve at any point and fairly accurately control boost target as a result. I've tuned it so that it's able to target anywhere from 5psi to 25psi depending on what's needed.  The target tables I've set up in that car are Gear vs RPM, so every gear has potential for a different boost (and torque) curve.   First and second gear have quite low boost targets, third gear actually has different target boost all the way through the rpm range as it's a stock RB25 gearbox - the boost targets have been chosen to maintain a peak of 600nm (what the owner has set as the maximum torque he's happy with putting through the stock 3rd gear) but it carries that to the rev limiter.   The boost curve to achieve that is something of a ramp up, then hold, then ramp up again and the power curve looks more like a flat line haha.  
    • so you can decrease or increase the boost depending on the diet as you wish?     by acting on the wastegate?
    • That's torque and power, it's all from a single run.  The boost curve is "held back" from it's peak target in the 3500rpm to 5000rpm range from memory, so it ramps hard to something like 18psi then climbs more progressively to 23psi nearer 5000rpm.   It makes the torque (and power) ramp more "natural" and less hard on parts and traction, it doesn't feel artificially held back.   
×
×
  • Create New...