Jump to content
SAU Community

Recommended Posts

ok so i have a bit of gear here for sale as im abandoning the project i had planned. NOT INTERESTED IN SWAPS!!!! cash only!!! should be able to work out a deal if your interested in combining stuff. no lowball offers either thanks. pm me or text/call 0401396905

1. rb26 head, complete except for covers. all standard. has some detonation damage. $1100

2.rb30 series 2 block&bottom end has been pulled apart. $100

3.rb26 intake setup. all standard, plenum to throttlebodies. all linkages etc. $500

4.rb26 exhaust manifolds and turbos and dumps. one turbo has blown seals. i think all lines are there.$150

5.r32 gtr intercooler. same condition as any 20 year old cooler. $100

6.r33 koyo aluminium radiator. few bent fins needs new filler neck. $75

7.545cc rx7 injectors. have been cleaned and tested. have resistor pack too.$500

8.r33 series 2 coilpacks and looms. $150

9.r32 handbrake lever and cables. $150

10.rb20 injectors x 5 have the 6th but its in pieces. $50

11.r32 brake calipers and project mu pads and slotted rotors. calipers have been fully rebuilt and painted in silver with black writing. $800

12.r32 gtr hks coilovers. not sure of spring rates but fkn stiff. $700

13.r32 gtr wheels x4 2 white 2 grey have tyre but they are old and bald. $450

14.engine stand. used t base type. $50

15.rb26 clear front cover. used. has pipe that goes across the front. $75

16.twin thermo fans au style i believe.$100

17.2 piece jap wheels unsure of brand. 16x7 and 16x8 +32ish offset. one wheels has been sandblasted in preparation for paint. $300

18.brand new tomei oil restrictors x2 $30 for both

ok i think thats it. throw me genuine offers. some stuff is self explanitory some need pics. let me know if you want a pic or if you want to come have a look. cheers Dale

Edited by daler32

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I know this one’s the BB one. My tuner did make mention about the actuator. I am curious about the VCT as well
    • Might also needs a stronger actuator with the right preloading. With older 2019 built bush G3 units, BB upgrade or 21U housing down size makes a pretty decent gain in response as well. 
    • Hey lads  so im finally putting together my rb30 forged bottom end and ran into an issue. I measured my main bearing clearance with arp main studs torqued to 60 ft-lbs using ACL H series STD size bearings and standard, un-ground crank shaft journals and got an oil clearance reading of about 1.3 thou measuring straight up and down and about 2.8 thou measuring at a 45 degree angle (just above and below the parting line). My machine shop said they measured the main tunnel and it was all within spec (they didnt say the actual measurement) and to go with a standard size bearing, which i have done and the clearance is too tight, I'm guessing because of the extra clamping force from the arp studs distorting the main tunnel. I was wanting to run about 2.5 thou main bearing clearance.  My questions are: 1. could i just use the HX extra 1 thou clearance ACL bearings? that would fix my straight up and down clearance making it about 2.3 thou, but then would the side to side clearance be too big at around 3.8 thou? 2. what actually is the recommended main bearing clearance for measuring near the parting line / side to side. i know its supposed to be bigger as the bearing has some eccentricity built into it but how much more clearance should there be compared to the straight up and down measurement? at the moment there is about 1.5thou difference, is that acceptable or should it be less? 3. If i took the engine block + girdle back to the machine shop and got them to line bore the main tunnel (like i told them to do the first time, but they said it didnt need it) what bearing size would i buy? the STD size bearing shells already slide in fairly easily with no real resistance, some even falling out if i tip the girdle up-side-down. If im taking material out of the main tunnel would i need a bearing with extra material on the back side to make up for it? this is probably confusing af to read so if something doesn't make sense let me know and ill try explaining in a different way. My machine shop doesn't come back from christmas break until mid January, hence why i'm asking these questions here. TIA for any help or info 
    • I bought the model back in Japan in Feb. I realised I could never build it, looked around for people who could build it, turns out there's some very skilled people out there that will make copies of 1:1 cars or near enough. I'm not really a photo guy... but people were dragging me in a group chat for the choice of bumper as someone else saw the car before it was finished as they are also a customer of that shop. I took the photo in the above post because I was pretty confident that the lip would work wonders for it. Here's some more in-progress and almost-done pics. It gives a good enough idea as to what the rear looks like!   I have also booked in a track day at the end of January. Lets all hope that is nothing but pure fun and games. If it's not pure fun and games, well, I've already got half an engine spare in the cupboard 
    • Well, do ya, punk? Seriously though, let's fu<king go! The colour and kit looks amazing on the car. Do you have any shots from the rear? I don't quite follow how the model came around. You bought the white kit and he modified it to match your car? Looks nuts either way!
×
×
  • Create New...