Jump to content
SAU Community

Nismo Clutch Disk + trust oil cooler

calvintys
 Share

Recommended Posts

calvintys Experienced

calvintys

Posted
Posted

As topic say i have a Nismo Clutch Disk only with box and everything even the nismo certificate. Anyway as i rushing for $$$ so therefore i need to let this go..

The product number is 30100-RN255. I bought it for $480 and now i am open for any reasonable offer as it is NEW haven been use at all. IT is a

Clutch Disc [Non Asbest]

Pull Type for sigle plate. Pressure=1050Kgf

std clucth is only 900Kgf

According to manual this clutch suit

G610 & G810 (L20)

CA18ET & RT18DET

HR31 GTS-R

S12 S13 RS13 (CA18ET, CA18DE, CA18DET)

PS13 (SR20DE)

BNR32 (RB26DETT) BCNR33 (RB26DETT)

R34 GTT (RB25DET) R33 GTST Not sure need to check

S30 (L20), HS30(L24)

KRZ31(VG30DE), WD21(VG30DE)

CZ32(VG30DETT)

Please let me know if any of interested by email at [email protected] or 0418 388 125

Also i have a Trust oil cooler which i am still considering if any of you interested pls let me know too. I am after 700 for the cooler itself

Calvin

Link to comment
https://www.sau.com.au/forums/topic/39360-nismo-clutch-disk-trust-oil-cooler/
Share on other sites
  • 9 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • PranK
      Hiya!

      By PranK · Posted

      Welcome!  Car sounds great, anypics ?
    • luke gtr
      Hiya!

      By luke gtr · Posted

      Welcome.  800hp should be a bit of weekend fun!
    • Kinkstaah
      Dose's Sometimes DIY and Pay Someone Home & Boat Improvement Thread

      By Kinkstaah · Posted

      I'm going with "Just run two gates". Fix the problem conclusively. It's the only way you'd ever truly know, right?. This is all pretty much splitting hairs. Even the extreme example where it takes two whole seconds at 100kmh or something sounds monstrously dubious. And anyway, when you're punching the throttle when you 'need' this power, you aren't at 2800rpm in the wrong gear. Test it at 5600rpm in 3rd gear, when you're traction limited punching out of a sweeper. Much difference there when you account for traction?
    • GTSBoy
      One Headlight isn't working - Driver Side Fuse Keeps blowing

      By GTSBoy · Posted

      And the full R32 GTR wiring diagrams are also freely available. Hmm.... there's supposed to be an auto replace that would have linked the thread. Here it is, manually  
    • dbm7
      One Headlight isn't working - Driver Side Fuse Keeps blowing

      By dbm7 · Posted

      Ahh...should have been clearer ~ there's 2 ... SMJ = super multi junction (connector)...   ...this is connector 6 & 25 in above image -- body harness to engine loom (6) & body harness to main loom (25) Headlights go to front via connector 6 ; fuel gauge goes to tank sender via connector 25  ...like I say this is R33 diagrams, but at a pinch R34 won't be too far different. *IF* the two ground faults are related, this can be the only place where both wires converge (as one runs to the back, the other to the front)... ....thing is, you probably need to establish if the faults are related (unless you examine that area and find obvious chaffing on the looms there to body ground)....*IF* the fuel gauge is still broken (full needle deflection), I'd be headed for the boot, remove fuel sender wire, key on and measure the voltage there ~ it should be roughly 10volts. If that's ok, check sender to ground resistance...if this is a dead short to ground (and there's fuel in it), then sender has failed or something funky has happened to wiring in the tank. edit: ahh...rereading the thread, this is R32....above fuel sender test still valid tho'
×
×
  • Create New...