Jump to content
SAU Community

Z32 Air Flow Meters - Dont Fit R32 Gtr ?

r32gtrv-spec
 Share

Recommended Posts

r32gtrv-spec Collaborator

r32gtrv-spec

Posted
Posted

hey folks

Now ive purchased a set of z32 AFM for my r32 GTR - i have the M'S k&n air filter pod and the manifold type things the pods connect to - the stock air flow meters connect up to them perfect, but these z32 air flow meters the 4 bolt holes are near 20mm wider and will not connect to it..

have i been given the wrong AFM's ?

i would assume that they should be the same size as stock, just able to handle greater flow ?? as i was told they are near as good as the nismo spec...

anyone running these AFM's let me know, cause it seems ive been sold the wrong size ? or to suit a different modle/make of car..

The M'S K&N induction the 4 bolt holes on the induction manifolds that hold the pods are the same bolt holes that the stock standard AFM's have. same hole pattern.

But thease z32 AFM's the bolt pattern is near 20mm wider and the AFM themself is much much bigger

any suggestions and/or ideas ??

muchly appreciated

cheers

Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Papichulo96
      Rb head oil drain dimensions

      By Papichulo96 · Posted

      Bump on this to not make another post, had a ‘head drain’ leak on me and have the engine out as we speak. Planning on just putting a new freeze plug back in , plug the tapped holes and just be done with that headache.    Now I still want to relieve pressure to allow oil to pass down the blocks returns easier. I’ve seen catch cans with multiple vents help folks with this issue on this forum.  I’m wanting to make my own. I have some pictures here of my setup if anyone can help how I should plumb and design the catch can I would deeply appreciate it !   rb25 Oil upgrades: 1.0mm restrictor n1 pump/billet gears extended crank collar  extended sump with trap doors/w welded fitting    
    • GTSBoy
      Need AC Compressor for R32

      By GTSBoy · Posted

      The Frenchy's kit is the way to go forward. A modern compressor that weighs about 1/2 as much, is at least twice as efficient, and will do a good job on R134a. And of course the kit has everything else you need to connect it up and have it work properly.
    • Zabuza
      Need AC Compressor for R32

      By Zabuza · Posted

      Hey all , I am in the process of having the AC system in my r32 GTST converted from r12 to r134a and I’m being told my compressor has gone bad and I will need a new one. I was wondering if anybody has any suggestions for what is the best route to go aside from dropping $1500 on a new oem one? I did see that Frenchy’s performance garage offers a kit to mount a Toyota compressor, has anybody actually used this kit on their car? Or is there anywhere I could purchase just a clutch? Any help is appreciated.
    • GTSBoy
      Help Understand GTT Boost Setup

      By GTSBoy · Posted

      Well, your RB20 ECU loom won't have wires for the boost solenoid, that boost sensor, and possibly one or two other things. There could be differences in seemingly random things like the charcoal canister purge solenoid, because the 25DET has to handle boost in the vacuum system and the 20DE does not. I don't know - I haven't looked. It is very likely that all the most important things are same-same, being the main sensors like AFM, CAS, etc, and the injectors and ignition. Not that you'll need the AFM for the Haltech anyway. I would suggest that you would seriously want to sit down with the pinouts for both ECUs and just go through them and highlight green what is the same, orange what is different/missing, and make a plan from there. It's not going to be difficult. It will either be the same or need to be fixed.
    • Sxnjeet
      Help Understand GTT Boost Setup

      By Sxnjeet · Posted

      yeaaa that's why I haven't done any wiring to the stock ecu harness because I have the haltech, but then that leads me to the other question of "is the pnp harness really plug and play?" or would I have to still switch some pins/wires over because the pnp is for the rb25det neo harness, and not for the rb20de neo harness. was really hoping to find something to spoon feed me since so many people have done rb20neo + t conversions, but man this is rough.
×
×
  • Create New...