Jump to content
SAU Community

Flutter noise - How?!?!?

[R31][Silhouette]
 Share

Recommended Posts

[R31][Silhouette] Contributor

[R31][Silhouette]

Posted
Posted

Hey Guys,

I've got a silvertop rb20det - I've asked this question before but never got a proper answer - does anyone know how to get the flutter (intercooler dose) noise

instead of the stock 'pssshht' noise?? Has anyone experimented and got results? People have said 'bigger cooler, more boost' but I'm pretty certain that's not the case!

Any ideas?

Cheers

Link to comment
https://www.sau.com.au/forums/topic/39443-flutter-noise-how/
Share on other sites
WHITE R32 Grand Master

WHITE R32

Posted
Posted

the sound u can hear is called compressor surge or compressor stall.... what it is is compressed air trying to come out of the air inlet on your turbo and hence trying to stop the wheels spinning... mainly cause u are using a small bov or no bov or have it set too tight.... this causes excessive pressure on your turbo and can cause premature failure due to excessive load caused by the stalling..... most cars will have a bit which is ok but if it happens alot and at high boost levels id look into getting a better bov....

basically what im trying to say is if u want the noise tighten up your bov or block it off though i dont advise this cause of the afforementioned circumstances.... dunno if that helps or not.... cheers Jon

Link to comment
https://www.sau.com.au/forums/topic/39443-flutter-noise-how/#findComment-801283
Share on other sites
[R31][Silhouette] Contributor

[R31][Silhouette]

Posted
  • Author
Posted
Steel, just make a cut out, this is not dangerous btw! Been running my car like this for 2 years without a bov at 14psi!

Hmm.. so do I remove the stock bov - by undoing those two bolts? then take that off and put a steel cut out in it's position? Is that right??

I've never removed the standard bov before - so don't really know what to expect!

Cheers

Link to comment
https://www.sau.com.au/forums/topic/39443-flutter-noise-how/#findComment-801295
Share on other sites
WHITE R32 Grand Master

WHITE R32

Posted
Posted

this is a very debatable issue as to weather or not it causes dramas with bearing wear etc ..... but after spending 2k on a turbo id hate to have a warranty voided by just wanting a "cool" sound.... its not worth it in my eyes.... but having said that ca18det's dont have a bov std and neither do alot of opther cars... but rb's have them for a reason and ill keep mine that way...

Link to comment
https://www.sau.com.au/forums/topic/39443-flutter-noise-how/#findComment-801296
Share on other sites
jaqule Grand Master

jaqule

Posted
Posted

BelGarien has a nice flutter affect in his BOV , he has a HKS SSQ and he has just removed the fins , I think he said , you may have to ask what he did exactly but I do know that he still has his BOV on

Link to comment
https://www.sau.com.au/forums/topic/39443-flutter-noise-how/#findComment-801301
Share on other sites
MSPEC Mentor

MSPEC

Posted
Posted

Nope, though its probably best not to do it on a standard turbo. I dont really mind who does or does not do it. Fact is I have always done it, for no real reason but its been fine. Benny boy at Race Pace aint fussed either way so nor am I.

Link to comment
https://www.sau.com.au/forums/topic/39443-flutter-noise-how/#findComment-801445
Share on other sites
DentonR33 Rising Star

DentonR33

Posted
Posted

Yer i did it and my turbo went bang :( probably would have happened regardless though as was running more boost.

I also did what steve did although i refitted the bov on top after i had put a steel plate over it. Then you have to block up two holes, a bolt works good on the smaller one and the end of a broom worked a treat on the other one. hehehehe :) weeeeeeeeeeee vromm chh chh chh chh

Link to comment
https://www.sau.com.au/forums/topic/39443-flutter-noise-how/#findComment-801480
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Komdotkom
      High temp brake fluid?

      By Komdotkom · Posted

      Reasonably hard, although I haven't run it with the new Endless setup yet. The old brakes were F50's on 335mm rotors and the car did a 1:40.6 at Phillip Island which is a reasonable time, I'm seeing high 600s on the temperature paint. A guy I know ran the Endless fluid at WTAC without issues and he was doing 1:33's I think (Evo) with a 355/332 setup. I don't get out to the track as much as I'd like but we put the car on the hoist and spanner check every bolt and re-paint mark everything, bleed the brakes, change the fuel, check the coolant system and re-bleed blah blah blah before every event. Motorsport is expensive, RB's are expensive so a couple of hours before an event is time well spent. It's also a net time saving because if you can keep your RB from self destructing it saves you time in the long term!
    • Duncan
      First/Second Post

      By Duncan · Posted

      Welcome Alice......hope you have a bit more luck from here on! What was done in the build?  
    • svenskalice
      First/Second Post

      By svenskalice · Posted

      Hello! I'm new here, I have an R33 GTST that is currently being finished up! Last year was pretty rough, blew two stock turbos so I decided to build the car. Has been down since November, but I get it back next weekend!
    • svenskalice
      Kaizo Industries

      By svenskalice · Posted

      Hello, I believe my car was imported to America in the 2000s by Kaizo Industries. Would anyone be able to help me find more info on them? I've only found all the basic stuff like that paul walker bnr34, them being shutdown by feds, just stuff like that. Any help would be much appreciated, thanks!
    • believer
      HKS Vcam Step Pro Issues

      By believer · Posted

      I am using Motec M150.  I am not working on the car myself actually.  My workshop is giving all these info, they are quite reputable in the industry and are very familiar with Motec and RBs and have done a few big setups with VCam and single turbo on RBs.  In fact, they built and tuned my engine from day one.  But they are stumped with my engine at the moment and cannot work out how come the compression is so low with the VCam. They told me that they have now swapped in some Kelford cams (without the VCam) and can achieve around 130psi compression and the low end torque is better, but now the engine is doughy as.  It boosts and peaks at more than 1000rpm slower, with twin HKS GTIII RS, it doesn't get full boost until over 5000rpm. I have always thought the VCam was a bit disappointing at the low rpm. To a point I had to ride the clutch a fair bit to get up a small hill from stand still.  That was when I had a clutch.  Now changing to a 8HP, I don't have that luxury and this problem has become a major issue. I am beginning to think the VCam never work since the day it was installed.  Maybe it was just sitting at the most advanced point, that is why it went good at top end but very ordinary at the bottom.  Therefore, with the help of the Holinger 6 speed and paddle shift, as long as it was moving, it drove pretty good.
×
×
  • Create New...