Jump to content
SAU Community

Recommended Posts

Hi All

I have a number of parts for sale. See bellow for prices and pics (or try http://118.127.2.168/carsale/):

Bosch 044 - brand new in box - $180

Blits Bonnet, brand new, never used, only thing done to it is to fit windscreen washers - $700 - ADR Approved aftermarket bonnet

Random Highflow cat, unknown brand, $120

RB26 front pipes, twin 3" inlet to 4" outlet, $220 - this things a monster and will flow bulk hp - will throw in a muffler that used to bolt to this for the flange, if buyer wants (shipping etc)

SuperSpark coilpacks to suit early RB25 and RB26 - Never used, in box, $350

R32 ReinHard Dual Tip Exhaust - Sits super tight in the tunnel, good for keeping ground clearance, 3", will flow heaps of HP - $500

SuperCat 3" Muffler /w flange and mounting brackets to suit the R32 ReinHard exhaust above, for swapping it on and off (noise etc) - $250 or $600 for both - flows well enough, good for shutting something right up.

HKS R33 Catback, 3.5", good for much HP again, some scratches to the bottom of it, $500

Gktech Dump and front pipe into CatCo high-flow cat, made to fit a RB25-equip R32, should fit R33 or RB20 R32 but unsure, 3 bolt flange, also comes with small tip off cat for track days, $150. Wrapped in heat-wrap.

R32 GTR JJR Adjustable Upper control arms, brand new never used in packet, up to 5 degrees negative camber, $300

Will post anywhere at buyers expense. Located in northside brisbane, pickup definitely an option.

My number is 0400 813 419

044.JPG

bonnet1.JPG

bonnet2.JPG

Cat1.JPG

Cat2.JPG

RB26FrontPipes1.JPG

RB26FrontPipes2.JPG

CoilPacks1.JPG

CoilPacks2.JPG

R32ReinHardtSYstem1.JPG

R32ReinHardtSYstem2.JPG

R32ReinHardtSYstem3.JPG

R32ReinHardtSYstem4.JPG

R32LegalMuffler1.JPG

R32LegalMuffler2.JPG

R32LegalMuffler3.JPG

r33Exhaust1.JPG

R33Exhauts2.JPG

R33Exhaust3.JPG

RB25FrontPipe1.JPG

RB25FrontPipe2.JPG

RB25FrontPipe3.JPG

UCA1.JPG

UCA2.JPG

Edited by IanB

Hey mate, sorry, thought I corrected this earlier, but it would seem not. The y-pipe is infact 300, but it would seem SAU wont allow me to edit the post. I tried to send you a PM on this, but it would appear your inbox is full or you are otherwise unable to receive messages. If the new price is still acceptable to you, I will get a shipping quote, otherwise, I do apologise for the inconvenience.

Regards,

Ian

Edited by IanB

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep that is correct. It allows you to adjust the short throw range from what I can tell
    • Car has been running great, I've put about 300km's of break in time on it. First thing that stands out with properly sealing rings is no more noticeable crankcase smell coming out of my catch can. This may seem insignificant, but the constant smell while driving around was infuriating. It's also nice to see my oil level remain stable. Two new issues have developed that I only noticed this weekend though. There's a very noticeable driveline vibration past 100kmh. I only noticed it now as I've been babying it under 100kmh in the backroads. This comes as no surprise as I'm running a one-piece shaft, and I paid zero attention to my driveshaft angle when I put everything back in. I also have a fair bit of voltage drop on hot starts. The starter audibly is forcing. No issues on cold start though. I must not have removed all the paint under my main block ground during assembly. I'll try and take care of both those issues this week once the kids are asleep.  I also received all the parts I was missing for my direct port setup. I will hopefully have pictures of that up soon. I'm hoping to get back on the dyno the week of June 30th as I'll be on vacation. I'm confident I should be able to make north of 500rwkw on pump gas and WMI. I'll go back again later this summer with E98, but I want to confirm my ethanol content sensor is working properly first. I've never seen it read anything but 11%. This makes sense for our 10% ethanol content pump gas here, but I would expect the occasional movement between fill ups. 
    • 75% complete. Will now need to get a new axle with 5x114.3 hubs and then figure out how to customize some mudguards for it once the wheels are on.
    • Trailer prep is underway... Lined up the wheel to get a rough indication of how it would sit Then removed all the bits (as far as possible) and gave the frame a light sand and quick lick of paint   Then added some carpet
    • okay, so I figured this out, removed needles and reinstalled after swapping the gauge face on my triple gauge for my ER34, all work and look good. I tried to do the same for the main cluster, but the main cluster gauge faces are dished, the replacement gauge face are flat, so due to the dish in the org face ,mounting backing plate (clear) and depth of the needle, the flat gauge face will not work. I notice that R34 gtr gauges are flat, appears to be different clear backing plate that aren't dished. are these available, or what have others done to install flat gauge faces?
×
×
  • Create New...