Jump to content
SAU Community

Recommended Posts

I'm still tossing up my next R-comp purchase, have A050 M at the moment in 265/35R18 and thinking of trying out some 295/30R18 if they fit but curious on how the Hankook Z221 perform considering the price, can also get them in a 285/30R18 which may be a happy medium in size.

So in terms of outright lap times, how would a 285 Z221 compare with a 265 A050M?

The big feedback I'm hearing from the IPRA guys since going from the 048's to 050's is not only that the grip levels seem much higher, but they maintain the grip almost to the end, and don't seem as bothered by heat cycles. The end result is that many are claiming better value for money as they're getting the full life out of tyres, rather than binning them (selling cheap) after a few heat cycles when there's still a lot of tread left.

Not sure how the Hankooks compare to 048's, but the 050's certainly crap all over the 48's.

A050's do seem to last a lot longer then A048's and still give good grip levels.

I have a good supply of Ao48's from the V9 utes series where teams would only run a set for one round and then off load them as the grip level had gone away. Many of these tyres still have heaps of tread but have lost a few seconds in lap times - but they are great for track days. By comparison the A050's are kept until they are down to the wear indicators as the grip level does not drop off as quickly.

How would the Z221 store compared to something like A050? My size is 235 45 17 and the Z221 M are $250ea in that size, I can't find A050 for less than $450ea

That's about right for the price difference.

I haven't run on either but I'd happily take the Hankooks. Yokohama had them banned from Superlap for a reason, and most of the people that buy new Yokos do so because their race rules require thenm.....

That's about right for the price difference.

I haven't run on either but I'd happily take the Hankooks. Yokohama had them banned from Superlap for a reason, and most of the people that buy new Yokos do so because their race rules require thenm.....

I didn't know that about Superlap, interesting!

For around the $250ea mark the Z221's seem like the best option, that's almost still KU36/RSR etc money.

I went to a track day at Marulan a few weeks ago and a couple of guys there were running them with big praise.

How would the Z221 store compared to something like A050? My size is 235 45 17 and the Z221 M are $250ea in that size, I can't find A050 for less than $450ea

Basically the same sort of difference for price in 18's. I don't really mind wear as much as I don't want to go backwards in time.

I ran on the Hankooks Z221's for the first time recently in my new bus as they are the control tyre for AMCamps.

These weren't the softs that the WTAC guys run. They were the normal compound. One interesting thing I found with them was they really took 3-4 laps to get up to temp and for the times to stabilize. They were a mega tyre for a race though as I was doing 10-12 lap sessions and from lap 4 on wards they were better - but not sure they would be the ideal option if you were only doing 3 lap sprints. As lap 1 was a good +2s slower than lap 4.

As an example here was one of the sessions I did at Winton. You can see the fastest lap was lap 7 and then it was pretty consistent after that.

1. 1:37.6933

2. 1:36.9572

3. 1:36.4395

4. 1:35.6922

5. 1:35.5647

6. 1:35.2582

7. 1:34.7901

8. 1:35.1124

9. 1:35.4962

10. 1:35.2636

11. 1:35.1733

My experience with A050's however is their best lap is lap 1.

  • Like 3

I ran on the Hankooks Z221's for the first time recently in my new bus as they are the control tyre for AMCamps.

These weren't the softs that the WTAC guys run. They were the normal compound. One interesting thing I found with them was they really took 3-4 laps to get up to temp and for the times to stabilize. They were a mega tyre for a race though as I was doing 10-12 lap sessions and from lap 4 on wards they were better - but not sure they would be the ideal option if you were only doing 3 lap sprints. As lap 1 was a good +2s slower than lap 4.

As an example here was one of the sessions I did at Winton. You can see the fastest lap was lap 7 and then it was pretty consistent after that.

1. 1:37.6933

2. 1:36.9572

3. 1:36.4395

4. 1:35.6922

5. 1:35.5647

6. 1:35.2582

7. 1:34.7901

8. 1:35.1124

9. 1:35.4962

10. 1:35.2636

11. 1:35.1733

My experience with A050's however is their best lap is lap 1.

Great info, from what others have said the Hankook soft is more like the A050 medium so I wonder if that makes a difference. Do you have times on a A050 to compare?

I tend to get my best lap on medium A050 on the 3rd hot lap, don't know if it comes down the driving style, tyre pressures or something else

No I don't have A050 data with this car. That was the first (and only) time I have driven it to date.

But I doubt the Hankook softs are like the A050 Mediums. The softs seem pretty special judging by what we've seen at WTAC.

I just checked and I was running the Hankook Mediums. As you say it may come down to tyre temps/pressures. We were aiming for 34 hot but that was after 10 laps, not 3. Maybe higher starting pressures would yield better results for early laps - I'm not 100% sure TBH. I just know I struggled to get them to "turn on" in the early laps each time out.

But I will also say the tyres I used had already done a 4hr race at QR and then I did a bit over 50 laps of Winton (just over 150km's) and they were still in pretty damn good condition so they certainly seem to wear well.

Hankook mediums are the wrong compound choice for sprints. Not fair to compare those to A050 Mediums - the comparable Hankook compound is C70 Soft. Edited this earlier quote to make it a bit clearer:

I learnt the hard way. Bought a pair of bargain secondhand 275 Z214 C51 "Mediums" for the back of the Soarer, only to find they were harder and less grippy than the 245 NT01s I had on there. I had NFI about the Hankook compounds at the time, but "medium" sounded like what I wanted for sprints. Wrong! They're not that old and had almost new tread, so at first I thought they might just have been cooked or heat cycled too many times. But a mate who runs C70s told me about the compounds... At least it was only $100 bucks wasted.

Then I bumped into the Hankook rep up here at a hillclimb and he explained the C70 "softs" as really being medium compound and the C50 "medium" is really a hard compound. C90 (supersoft) for Hillclimbs/WTAC. C70 (soft) for Sprints and short races. C50 (medium) if you want to do a 3hr race!

Edited by hrd-hr30

Found this which is interesting

Have used RE55S, A050-M and Z221 C70 (soft). Z221s are awesome. Compared to A050 the difference in lap time so far has been around 2 seconds, but there's more in them, just have to get used to the grip. Though I have gone from 255/40/17 and 265/35/18 in A050-Medium compound to 265/35/18 and 285/30/18 Z221 soft so it's not a like-for-like comparison. In terms of actually driving the car there is less understeer, but when the car does understeer you still get better cornering ability compared to A050. Finally the Z221s seem to be able to be bullied a bit more. I pretty much killed a fresh set of A050-M at Winton by pushing too hard into the hairpins but with the Z221 you can push and they won't chunk out.

In terms of size, the future is 285-square or GTFO...

RB is right you have about 3 optimal laps then the grip starts to slide off, my car is generally only good for 3-4 laps anyway before it starts to get a little hot so for me the soft compound is perfect.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I've done a few BMS systems. Code in Canada use to force us to have any safety components outside of the PLC but with a code change back in 2018 I believe it was, we can now use safety PLC's to control everything. Sadly to your point, AB Guardlogix safety instructions for example are only available in ladder.  Machine safety is a very big thing here though, you're constantly forced to migrate to the next best thing by OSHA. I honestly prefer safety plc's, including anything from AB more then I do working with old school safety monitoring relays. PLC is only one portion of it, the rest of the electrical still has to follow to meet SIL (Mechanically linked dual contacts, bla bla)  Now tell me how to feel about safety over comm's (e.g Ethernet/IP CIP) on a unmaintained network haha
    • To your point, boolean logic. We're not only working with bools in ecu's, so it's very limiting. I wanted to setup a low WMI pressure alarm. After 1 second I want WMI line to hit 100PSI, 2 seconds 175PSI, etc. and trigger an alarm if it doesn't meet those thresholds. This would of taken me one very short line of text, but instead I had to bugger around with generic timers, conditions, etc. and so forth.
    • I much prefer that to an actual oil pressure issue, never would of thought it would of been a volt drop issue but SAU brains win again. Guess ill be turning down the oil pressure limit for the track and hunting some grounds. Ill hopefully update this thread with some high oil pressure and solid ecu voltage logs. 
    • You've just discovered a really good reason to tell yourself, yes, I do need to buy an aftermarket ECU. Put the MAF in the bin. Slap in the new ECU and have a think about what turbo sounds you prefer.  Do you want a 90's style BOV wooosh? Do you want a hektik tsututututu?  Mate, can't go wrong. Just gotta get that ECU and the world is your oyster. 
    • Hi. Iam just curisou about this topic. I saw this video. It is about Greddy Type FV2. I know that BoVs are about that sound but how and when to use it? I read some topic here and from what i have understand on stock RB with MAF there will be some "problems" if you use this BoV? It vents the air in to the atmosphere and the MAF on stock car needs this air back in to the intake and not out? Or is it wrong? If so...i saw you can put some adaptor to circule air back...but does that not "loose" that sound? I saw another BoV from Turbosmart and it has two "exhaust" like ports? One is for the stock tubing for letting air back and one is for "sound" and let the air in the atmosphere? Can someone please explain? This is the Greddy one:  And this is the Turbosmart.     THANK YOU!! EDIT: So i read about this topic some more and i if i understand that correctly: That Greddy can function either like BoV or 100% Bypass valve? And that Turbosmart is what they called hybrid so you can adjust what and how many air can be vented out or back in? Is this right? THX!
×
×
  • Create New...