Jump to content
SAU Community

Recommended Posts

Hey guys this just an EOI (Enquire Of Interest) to see if there is any interest in my skyline. A bit about the car it was a personal import back in 2008 my cousin bought it from a trader and barely drove it as he had r33 as well and was bare stock only had a 5zigen cat-back. Ive owned the car now for 2yrs+ and it has been my project and i barely drive it as im on P's :( its sees the road probably 2 times in a month. Car is immaculate and i have to say one of the cleanest 32s going around for sure.

Some mods:

Exterior:

-Ful vertex kit (copy but no ebay crap) fitted in June last year cost me $1200 for the kit from japwarehouse tullamarine.

-Carbon fibre hood GTR style cost me $1000

- GTR spoiler

- GTR headlights with amber indicators

- GANODOR style mirrors

All work was done by Excelsior panels

Interior

- Nismo short shifter and gear knob

- Genuine Red leather and suede seats

- suede steering wheel

-Clarion DVD player

- Has a HKS EVC 4 boost controller but is not connected all wired up solonoid not hooked up

- Blitz boost gauge

Engine: Is slightly moded with the basics and is clean as!

- GREEDY SPEC LS TUBE AND FIN intercooler $700

- Custom split dump pipe

- Blitz front pipe $350

- Xforce Hiflow Metalic cat not ceramic $250

-Pod filter

Thats all i can think of atm. Car has done 61XXXkms and runs so smooth and clean :D

Its manual

Can come with rego till next year january 2013

Does not come with lenso d1rs comes with standard gtst wheels.

Im looking for 11k with rego but offers will be considered but by saying that nothing stupid NO LOW BALLERS people who know this car know its meticulousy looked after and cared for, always serviced with MOTUL oils and DRIFT filters.

If the a good offer is on hand may consider

You can SMS me on 0433476929 and ill get back to u asap

Located In northern suburbs melbourne

Thanks for looking

post-77571-0-50498100-1332162783_thumb.jpg

post-77571-0-66966800-1332163235_thumb.jpg

post-77571-0-14962000-1332163258_thumb.jpg

post-77571-0-00476200-1332163274_thumb.jpg

Edited by shev
Link to comment
https://www.sau.com.au/forums/topic/395281-eoinissan-skyline-hcr32-gtst/
Share on other sites

Looks like a really nice 32 mate. Throw up some pics of the interior and an engine back pic, will really help

Thanks mate spent a lot of time to get it to where it is now.

As asked more pics of engine and interior

post-77571-0-28458900-1332195245_thumb.jpg

post-77571-0-20822600-1332195256_thumb.jpg

NO LONGER AN EOI!!!

Been thinking long and hard now and its gonna be very regretful but i want to sell her to make way for a something new :(

So im taking resonable offers can work something out if people are intrested!

Thank you

  • 2 weeks later...

EOI is a acronym for "expression of interest", I expressed my interest in this car.

Read the rules boys, even though you hate rules, point one would be good point to start at, http://www.skylinesa...92#entry1281592

OP also asked for "all reasonable offers" I thought my offer was reasonable, he could say no....

Thankyou very much, come again.

If you read the rest of the comments on the post it says "NO LONGER AN EOI"

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Do the R32s run high or low impedance injectors?
    • It may not feel like it to your wallet....but sounds like this was one of those "lucky you did it" rebuilds. Hopefully you have better luck this time
    • It's aftermarket. It also reeks of Honda Civic tryhard from 2003. But if you want one....then you want one.
    • Well some mostly good news and some slight bad news.  Good news is cylinder 6 did in fact only require a honing and I'm good to run my 86.5mm pistons again. I should also get the block back by end of week. Bad news, had a few surprises pop up. First, main and rod bearings were trashed. No sign of any heat damage. I knew right away what caused this... I had not packed my oil pump originally and spent a lot more time than I would have liked cranking the motor to get oil pressure. It sounded fine once started so I chucked it up to luck and forgot about it. Luckily rod and crank are fine and just need new bearings. Engine builder agreed that this was the cause.    Another surprise that carbon covered up very well that I didn't catch, something got sucked up and went through cylinder 1, 2 and 3. Luckily this was no cause for concern, just needed a bit of cleaning up. Valves look fine but he will vacuum test the head this week to confirm. I'm presuming this was something left over from welding my intercooler piping, but we'll never know. I'm going to thoroughly reclean everything.    So all in all, happy the motor is fine, and I'll get it back much sooner than expected. I'll also be taking the time to convert my WMI system over to direct port. I'll snap some pictures of that when the parts come in. 
    • I understand, thanks. Yeah I wouldn't want the car to tip over, I'll try and use the sills, I don't want to risk smashing the chassis rails. I ordered some rubber pucks that have a hopefully big enough slotting. If the front right gives me trouble I can always just make a wood block. I'll measure and inspect the sills closer once I actually take the car up. I hope so, but the rubber blocks I had in hand so far were pretty damn firm, if they are that hard they won't give much way. I'll let you know what happens. Angle grinding rubber isn't one of my favorite tasks. I'll probably start a build thread soon, for my own documentation and "log" as well as sharing what's going on with the car.
×
×
  • Create New...