Jump to content
SAU Community

Catch Can/bov Plumb Back

Manuel Kasko
 Share

Recommended Posts

Manuel Kasko Grand Master

Manuel Kasko

Posted
Posted

Hey guys,

So just installed the new intake pipe and its causing me a few drams with fitting.

At the angle it needs to be to fit on the turbo correctly and fit the pod it seems to leave me no room for the plumb backs.

Here is a picture of how the hoses sit right now.

Do you think this will get way to hot and melt?

015uuo.jpg

Link to comment
https://www.sau.com.au/forums/topic/395489-catch-canbov-plumb-back/
Share on other sites
scotty nm35 Grand Master

scotty nm35

Posted
Posted

I made it to suit the stock airbox but I would have thought a pod would be fine. Do you have better pics of the area inc pod? Perhaps you need to cut the top bend off the pipe.

You can buy silicone covered fiberglass hose protection but even a little exhaust wrap would work. How does it line up with the BOV pipe?

Any problems let me know, I haven't done a remote install before. :)

scotty nm35 Grand Master

scotty nm35

Posted
Posted

The picture makes my head hurt. lol.

Can you see how it would sit if you cut the top bend off? It would give you plenty more clearance but then the BOV wouldn't align as well. Keep that as a last resort perhaps.

Can you fit up the BOV/breather pipe and see where it sits, the pipes need to bend a bit yet I would say. What is the pod hitting to stop it dropping down more? You may need to trim the 80mm joiners down a little too for more room.

SargeRX8 Grand Master

SargeRX8

Posted
Posted

I now use the stock pipe. It didn't line up anywhere near the BOV return on my intake pipe, so I cut it up at a certain point where it would angle down towards the return point in the intake pipe then used the rest of the rubber pipe to fill the gaps. I'm still using the same stuff for my oil breathers but they don't sit as close to the manifold as the BOV return did.

Its funny, I had these 90 degree PVC couplings to create bends in the BOV return where I needed them. They lasted fine, except for the one ontop of the turbo, it shrunk and melted like a motherf**ker lol.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Shoota_77
      Car Rotisserie

      By Shoota_77 · Posted

      Hi guys, has anyone either purchased or built themselves a rotisserie for their car before? I can only just justify the need for one hence why I should just make one but at the same time, if I make one I can kiss another 4 weeks of potentially productive car working time goodbye because I'm building a bloody rotisserie....  I mainly want it for the application of the body deadener.  Cleaning the old stuff off, priming and then colour over the deadener doesn't worry me, it's just the application using the Schutz Gun that I feel would achieve a significantly better finish painting it side on and keeping the Schutz Gun upright.  I don't think they would work well on the side let alone almost upside down for some areas.  If the product I use (Terosun, etc) could work through a HVLP ok then it might be ok to apply without the rotisserie.   I can get one of these style ones for about $1200 which is pretty good value-     I reckon if I made one it would cost around $500 but it's more the time that it would take is more of a killer than the cost.  They look to hold their value pretty well second hand so I could always sell it after using it and realistically only lose $200-$300 at worst.  Or keep it and buy another project when this one finally sees the light of day... Anyone selling one...? Cheers!  
    • GTSBoy
      Stock rb25det neo questions

      By GTSBoy · Posted

      While it is a very nice idea to put card style AFMs into the charge pipe (post intercooler, obviously), the position of the AFM and the recirc valve relative to each other starts to become something that you really have to consider. The situation: The stock AFM is located upstream the turbo, and the recirc valve return is located between the AFM and the turbo inlet, aimed at the turbo inlet, so that it flows away from and not through the AFM. Thus, once metered air is not metered again, neither flowing forwards, or backwards, when vented out of the charge pipe. When you put the AFM between the turbo outlet and the TB, there is a volume of pressurised charge pipe upstream of the AFM and there is a volume of pressurised pipe downstream of the AFM. When the recirc valve opens and vents the charge pipe, air is going to flow from both ends of the charge pipe towards the recirc valve. If the recirc valve is in the stock location, then the section between it and the TB doesn't really matter here - you're not going to try to put the AFM in that piece of pipe. But the AFM will likely be somewhere between the intercooler and the recirc valve, So the entire charge pipe volume from that position (upstream of the AFM, back through the intercooler, to the turbo outlet) is going to flow through the AFM, get registered as combustion air, cause the ECU to fuel for it, but get dumped out of the recirc valve and you will end up with a typical BOV related rich spike. So ideally you want to put the AFM as close to the TB as possible (so, just upstream of the crossover pipe, assuming that the stock crossover is still in use, or, just before the TB if an FFP is being used) and locate the recirc valve at the turbo outlet. Recirc valve at the turbo outlet is the new normal for things like EFRs anyway. In the even of a recirc valve opening dumping all the air in the charge pipe, pretty much all of it is going to go backwards, from the TB to the recirc valve near the turbo outlet. But only a small portion of it (that between the TB and the AFM) will pass through the AFM, and it will pass through going backwards. The card style AFMs are somewhat more immune to reading flow that passes through them in reverse than older AFMs are, so you should absolutely minimise the rich pulse behaviour associated with the unavoidable outcome of having both a recirc valve and an AFM in the charge pipe.
    • joshuaho96
      Rb25det Belts Change

      By joshuaho96 · Posted

      Yep, in my case as soon as I started hearing weird noises I backed off the tension until it sounded normal again. Delicate balance between enough tension to avoid that cold start slip and too much damaging things.
    • silviaz
      Rb25det Belts Change

      By silviaz · Posted

      nvm this comment
    • silviaz
      Rb25det Belts Change

      By silviaz · Posted

      I'm almost at a point where I feel like changing the alternator. Need to check the stuff you mentioned first though.
×
×
  • Create New...