Jump to content
SAU Community

Recommended Posts

I'm probably going to be looking into bags for my sedan around next year as its impractical to have a car lowered at all where I live and I plan on keeping her for a long time and putting a bit of work into hense the decision

im factory ride height with after market 18x8f and 18x9r with 235/40 R18s all round (bit of stretch on the rear and none on the front)

i scrape front if i take it nose on, if i angle i dont.

with a full car load i scrape aswell, but most times im good.

Because???

Many people have done this and recommend it.. lowers by about 25mm without sacrificing too much ride quality.

I can't imagine lower mine any further. Don't know what ride height i'm on but it's stock and i'm scraping everyday i drive.

im factory ride height with after market 18x8f and 18x9r with 235/40 R18s all round (bit of stretch on the rear and none on the front)

i scrape front if i take it nose on, if i angle i dont.

with a full car load i scrape aswell, but most times im good.

technically you are not factory ride height anymore because you are running 40 profile instead of 45. You are approx 20-30mm lower than factory with those tire profiles.

mine has always scraped.

back when i had standard shocks and springs with 18x8 +35 factory premium alloys and 235-40-18 tyres.... the standard springs had so much travel that the under engine plastic panel would drag along the ground AFTER bumps in the road... the worst suspension ive ever driven on.

small.jpg

now with 2003 model 350z shocks and springs with 20x8.5 +35 235-35-20 up front and 20x10 +42 265-30-20 stretched in the back..... i rarely scrape under the car, but always drag the custom front lip (its lower than parking bay concrete blocks.... an upright iphone barely fits ) and the rear muffler drags occasionally when reversing over driverway gutters.

have only slammed the chassis rails once.

and even with 250kg of fat people in the back seat, the rear only dropped an inch

e1b25a02.jpg

fyi: the 350z shocks and springs originally felt way too stiff for my liking... but ive grown used to them and am quite happy with the ride. And theyre not stupid low either. Nightcrawlers is definitely lower than a slugs scrotum.

Edited by Deep Dish V35

Tyre sidewall height of a 235/45 is 105.75mm. The sidewall height of a 235/40 is 94mm. Overall tyre diameter changes by 23.5mm but radius only differs by 11.75mm (axel to tyre edge) which is the amount the axel will be closer to the road.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi everyone, I'm generally new to DIY projects, and I've browsed this forum and watched a lot of youtube videos but still have a few questions   Firstly, how does spray painting interior hold up? in particular like vinyl parts, my current mode of thinking is to use methyl spirits to take off original paint, clean/prep well, light coats, no primer or clear coat    Secondly, what is recommended for the headliner and, for example (my car is a r34), the A-pillars which are some kind of other fabric material, do you think I would be successful at retrimming these? or would it be better to go down the blacking out via Dupli-Color Vinyl & Fabric Paint    Any other advice / tips / tricks for refreshing/modernising these interiors?    Thanks
    • As title says  Pm a photo with what u have  Type m style would be good As Hidding a thick front mount
    • Just note that when trying to find a short in a globe power supply, it is best to disconnect the globe as it will allow current through to earth. With it unplugged it is easier not to get confused. Also with the r32 wiring, the high beam has 2 power supplies (one when you push the switch forward and the other when you temporarily pull it back; so if it is the high beam blowing you will need to trace both circuits
    • $75 Location: Gold Coast  Can post via Australia post
    • That's a short. Find the short. It will be somewhere between that fuse and the headlight. Start by removing the plugs from the back of the headlight and dimmer switches, and measure resistance to earth. Supply side (power from the fuse) should have none. The other side should have resistance compatible with whatever globe(s) is there (which is relatively easy to say for a normal globe, perhaps not as easy to say for LEDs). Anyway, if you have very low resistance, you defo have a short. Then you just have to run the wiring like you're running the bowel of a dog (on the operating table) that has swallowed something it wasn't supposed to.
×
×
  • Create New...