Jump to content
SAU Community

Recommended Posts

I got most of the wiring loom when i got the lights but i need help sorting it out, so here it goes.

Taken from another post about the spotlights - helps a little.

post-72216-0-28420600-1333687048_thumb.jpg

How i can best describe the wiring, just one side - both sides seem the same.

post-72216-0-47490500-1333687104_thumb.jpg

In this picture I dont know where plug A goes. Plug B and C fit the Fog light, i suspect the blue, black and orange wires should have the same plug type as Plug C.

Photo of the loom.

post-72216-0-37253600-1333687140_thumb.jpg

Photo of the plugs.

post-72216-0-43951600-1333687160_thumb.jpg

Photo of the switch (on dash).

post-72216-0-32817900-1333687177_thumb.jpg

Any help or photos appriciated - hope to get this finally sorted out on this forum once and for all.

Link to comment
https://www.sau.com.au/forums/topic/397104-stagea-dayz-spotlights-wiring/
Share on other sites

I got most of the wiring loom when i got the lights but i need help sorting it out, so here it goes.

Taken from another post about the spotlights - helps a little.

post-72216-0-28420600-1333687048_thumb.jpg

How i can best describe the wiring, just one side - both sides seem the same.

post-72216-0-47490500-1333687104_thumb.jpg

In this picture I dont know where plug A goes. Plug B and C fit the Fog light, i suspect the blue, black and orange wires should have the same plug type as Plug C.

Photo of the loom.

post-72216-0-37253600-1333687140_thumb.jpg

Photo of the plugs.

post-72216-0-43951600-1333687160_thumb.jpg

Photo of the switch (on dash).

post-72216-0-32817900-1333687177_thumb.jpg

Any help or photos appriciated - hope to get this finally sorted out on this forum once and for all.

Hey mate theres a grey plug near the drivers side head light or behind it that the relays and main loom plug into. In the car the switch has a earth and then theres a connector near the throttle cable on the fire wall pretty sure it a 2 wire connector. If u need more info let me know and I'll take photos and send them to u

  • 2 weeks later...

so it seems im missing a few parts of the loom, from what i can gather there is a

1 the loom that switchA plugs into by plug D, that then goes to earth and a plug beside the drivers foot (yup we have a plug).

post-72216-0-30972400-1335602569_thumb.jpg

post-72216-0-07837800-1335602681_thumb.jpg

2 the loom that plugs into next to the battery to the relays (plug A)

post-72216-0-55679900-1335602849_thumb.jpg

3 also missing the plug in the loom above (unknown wires) that i believe will be the same type as plug B but not sure if it should be Male or Female.

Any light shed on this would be great - or even if you have these parts or a full loom laying around, i would be interested.

Cheers

  • 7 years later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi. A little bit of an update. It maybe(hope not) looks like i would need a new tranny(it would be "maybe" a cheaper or better option anyway) So i need some info. I know i need a different propshaft(i can make custom one) LSD is not a problem cuz the engine will be still(for now) N/A RB20. So if i buy RB25DET NEO tranny...is there something else i need? I read something about push/pull type but i do not know if i need to "change" something or i can just plug n play onto my engine a go? Thanks for the advice  
    • Good morning all, Bit of a random question but figured I’d finally throw it out after wondering for a long while. Before I start, I'm hoping to do this purely out of personal preference. I think it would look better at night, and don't mind at all spending a few hours and dollars to get it done. I've copied this from a non-Skyline specific forum, so I apologize for the explanation of our headlight switch setup that we all know. Here we go: Zero lights (switch off) Parking lights (switch position 1) being a rectangular marker on the outside of the housing, my low beam being the projector in the centre (position 2), and a high beam triggered by my turn signal stalk. Most North American cars I’ve owned of this era have power to the amber corner (turning indicator) light as part of the first switch (parking lights). I’d love to have these amber corners receive power when the headlights and parking lights are on (headlight switch), yet still blink when using the turn signal which is of course a separate switch. Hopefully I’ve explained my question correctly. Is anyone aware of a way in which I might be able to achieve this? Thanks in advance
    • My heads are cathedral port! It's likely possible, but I don't want to add any extra moving parts (I know they don't move) between the heads, manifolds, etc. It will also affect how injectors/fuel rails etc sit and I don't really know if it would change how the FAST manifold goes/sits/fits. I have the LS6 steam pipes already as I have a very late LS1 block so it should be fine. I couldn't find anyone who had ever actually used one for this purpose, it seems 100% of people grind the water pump. The thermal spacers are 12mm and are half way to the cost of the newer water pump anyhow... so if it comes to that I suppose I'd rather buy a new pump. The bearing in the pump I do have is a little.. clunky, but it hasn't done that much time and I never noticed it when the car was together in the past few years, so..
    • The bushing has failed, not all that uncommon for a car of this age.  Any mechanic should be able to push in a new bushing for you, or you can probably buy the entire lower control arm, complete with bushes.
    • Could you not use "thermal" spacers to give the clearance, like the ones I used between the blower and head? That raised the manifold height by around 10-15mm Albeit the ones I used were for cathedral ports, but I assume they have similar for rectangular ports????
×
×
  • Create New...