Jump to content
SAU Community

Recommended Posts

  • Replies 7.5k
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

spotted a black 32 gtst this morning @ hancock road we went all the way to cambeltown oval

then @ 7:15 spotted white GTSt 33 on greenhill road we each gave each other the look over whilst possibly wondering r we both from SAU

possibly spotted pixel8r on greenhill road this afternoon if it wasnt him it was another Stagea i know it wasnt tangles :D

woohoo I got spotted at last!! :no:

yeah that would be me on greenhill rd. White series 2 stag. now with 50% more power than what it had back when you saw it at the cruise (august was it?).

Just out of interest, does anyone know of another series 2 stagea in adelaide?? (most notable differences are clear rear indicators and different front grille/separate hi-beam lights etc.)

I've seen about 8-9 different s1's, but no other s2's yet...

Spotted a nice silver 32 at Darlington hungry jacks on sth rd bout 9ish.

was checking out the car and didnt realise there was a driver :D he spotted me and I think he waved so might have been from here... if you are, sorry i didnt wave back, was totally out of it haha

spotted leeman's R34 in city BP, very very nice, cleanest R34 i have ever seen :D

cheers maxx, nice to meet ya! catch up with ya soon.

saw numerous skylines ( mostly 33's ) in town tonight as i did my first blockie! yay lol! my mum would be proud!!!

spotted white R33 with a decal panda as well and saw a diff 1 the other day without decal :S not sure if it was the same

post-13315-1154603022.jpg post-13315-1154603054.jpg

spotted this again on my way out of chruch today doesnt sound very loud was going up golden grove road towards the old moto cross bike track

post-13315-1154603022.jpg post-13315-1154603054.jpg

http://www.skylinesaustralia.com/forums/in...st&id=49782

Edited by Madaz
Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • I know this one’s the BB one. My tuner did make mention about the actuator. I am curious about the VCT as well
    • Might also needs a stronger actuator with the right preloading. With older 2019 built bush G3 units, BB upgrade or 21U housing down size makes a pretty decent gain in response as well. 
    • Hey lads  so im finally putting together my rb30 forged bottom end and ran into an issue. I measured my main bearing clearance with arp main studs torqued to 60 ft-lbs using ACL H series STD size bearings and standard, un-ground crank shaft journals and got an oil clearance reading of about 1.3 thou measuring straight up and down and about 2.8 thou measuring at a 45 degree angle (just above and below the parting line). My machine shop said they measured the main tunnel and it was all within spec (they didnt say the actual measurement) and to go with a standard size bearing, which i have done and the clearance is too tight, I'm guessing because of the extra clamping force from the arp studs distorting the main tunnel. I was wanting to run about 2.5 thou main bearing clearance.  My questions are: 1. could i just use the HX extra 1 thou clearance ACL bearings? that would fix my straight up and down clearance making it about 2.3 thou, but then would the side to side clearance be too big at around 3.8 thou? 2. what actually is the recommended main bearing clearance for measuring near the parting line / side to side. i know its supposed to be bigger as the bearing has some eccentricity built into it but how much more clearance should there be compared to the straight up and down measurement? at the moment there is about 1.5thou difference, is that acceptable or should it be less? 3. If i took the engine block + girdle back to the machine shop and got them to line bore the main tunnel (like i told them to do the first time, but they said it didnt need it) what bearing size would i buy? the STD size bearing shells already slide in fairly easily with no real resistance, some even falling out if i tip the girdle up-side-down. If im taking material out of the main tunnel would i need a bearing with extra material on the back side to make up for it? this is probably confusing af to read so if something doesn't make sense let me know and ill try explaining in a different way. My machine shop doesn't come back from christmas break until mid January, hence why i'm asking these questions here. TIA for any help or info 
    • I bought the model back in Japan in Feb. I realised I could never build it, looked around for people who could build it, turns out there's some very skilled people out there that will make copies of 1:1 cars or near enough. I'm not really a photo guy... but people were dragging me in a group chat for the choice of bumper as someone else saw the car before it was finished as they are also a customer of that shop. I took the photo in the above post because I was pretty confident that the lip would work wonders for it. Here's some more in-progress and almost-done pics. It gives a good enough idea as to what the rear looks like!   I have also booked in a track day at the end of January. Lets all hope that is nothing but pure fun and games. If it's not pure fun and games, well, I've already got half an engine spare in the cupboard 
    • Well, do ya, punk? Seriously though, let's fu<king go! The colour and kit looks amazing on the car. Do you have any shots from the rear? I don't quite follow how the model came around. You bought the white kit and he modified it to match your car? Looks nuts either way!
×
×
  • Create New...