Jump to content
SAU Community

Recommended Posts

So currently putting a list together on what mods ile be doing to my 25, have a 8g budget im working with too achieve close too 400hp and build my 32 into a drifter, will never be rego'ed again.

currently im going with

definite mods

HyperGear G3 turbo

DW300 in-tank fuel pump

740cc Deatschwerks injectors

Maybe mods

EWP

6boost midmount

Greddy manifold

But im stuck deciding if i should go with E85 or a WMI setup, both have there pros and cons, for me E85 is harder too buy as im in queensland but the power gains and and anti det will be alot more then WMI, but WMI will bring my temps down, engine will run alot cleaner and is easy to get...or run 50/50 E85 and 98ron...hummm

any advice will be appreciated,

Thanks in advance!

Edited by 51NNA
Link to comment
https://www.sau.com.au/forums/topic/397600-wmi-or-e85-stuck-on-a-choice/
Share on other sites

you can easily run WMI on E85, but now your talking some serious power lol more than you will push from a G3

for a track dedicated car in a non E85 friendly area, WMI will be easier to make do with.

once E85 is easier to come by you wont be at too much of a loss to retune and on sell the WMI kit. The WMI kits are under $500 for something that will do the job.

Why is E85 hard to get for a track only car in brisbane? There's a caltex at goodna which sells it, you'd go past that on the way to QR. There's also one in ipswich itself, a few over on the bayside and one near mt gravatt.

WMI is a BC E85 or agrestic Oz [where E85 is unavailable] solution. If you have good access to E85 and never travel outside the metro area/s then use it - its cheaper and easier to set up than WMI. For all us erudites unable to take advantage of E85, WMI is the answer.

I think the question that determines which way you go is how often do you drive the car. A lot of k's will mean WMI.

I'd like to see someone try a little straight water with E85. You would spray 1/2 the volume that you would if using a WMI setup for the same power level. Around 400cc for 400kw atw.

The advantage I see is that you could run the E85 tune a lot leaner, into the 12.x:1 range. Which will help a little with fuel economy in the long run. I can't remember exactly, what he told me but Piggaz's car drinks E85 at a pretty alarming rate. Well over 10lt/minute at wide open throttle.

From what I understand about E85 tuning, rich AFR's under full load are needed to help keep detonation at bay and also to keep things from getting too hot. In this way E85 tunes more similar to pure methanol burning engines than ULP.

Im running a Microtech LT12s btw, its going to be a track car so distance isnt that much of an issue, you use around 45% more fuel when your on E85 because to get the same amount of energy from the fuel you require alot more, just like Avgas, i just dont want to have to bring 100LTs of E85 too every drift event lol

Can someone explain how you'd do the 50/50 ethanol mix, does this mean mixing fuel at home from a drum or would you have 2pumps at the servo, one for 98 and one for ethanol?

What kind of gains would you get from 50% mix if your making say 300kw with 98?

id say get 2 20lt drums and put both in your fuel tank, i wouldnt buy e85 from the pump, only the drums, i assume it would be simlar gains too straight E85 but not as much, would also require less fuel then straight E85

just go flex-fuel setup.

Ethanol content sensor

ECU with digital input (Link G4, some of the Haltechs etc)

And get some ID1000's at least, to leave you some headroom if you change your mind. Better injectors anyway.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Price seems pretty good to me. Also seems a hell of a lot cheaper then buying another vehicle that only ever gets used for towing.  I'm a long way from you mate, I'm a couple of hours out of Brizzy. 
    • New [400]Z, they're available in manual and you don't have to worry about parts scarcity. 
    • Just planning to have the wiring neat and hide as much as possible.
    • The sodium acetate, mixed with citric acid, doesn't actually buffer each other. Interestingly though, if you used Sodium Acetate, and acetic acid, THAT becomes a buffer solution. Additionally, a weak acid that can attack a metal, is still a weak acid that can attack a metal. If you don't neutralise it, and wash it off, it's going to be able to keep attacking. It works the same way when battery acid dries, get that stuff somewhere, and then it gets wet, and off it goes again breaking things down. There's a reason why people prefer a weak acid, and it's because they want TIME to be able to be on their side. IE, DIY guys are happy to leave some mild steel in vinegar for 24 hours to get mill scale off. However, if you want to do it chemically in industry, you grab the muriatic acid. If you want to do it quicker at home, go for the acetic acid if you don't want muriatic around. At the end of the day, look at the above thumbnail, as it proves what I said in the earlier post, you can clean that fuel tank up all you want with the solution, but the rust that has now been removed was once the metal of the fuel tank. So how thin in spots is your fuel tank getting? If the magazine on the left, is the actual same magazine as on the right, you'll notice it even introduces more holes... Well, rust removal in general actually does that. The fuel tank isn't very thick. So, I'll state again, look to replace the tank, replace the fuel hanger, and pump, work out how the rust and shit is making it past the fuel filter, and getting into the injectors. That is the real problem. If the fuel filter were doing its job, the injectors wouldn't be blocked.
    • Despite having minimal clothing because of the hot weather right now, I did have rubber gloves and safety glasses on just in-case for most of the time. Yes, I was scrubbing with my gloves on before, but brushing with a brush removes the remaining rust. To neutralize, I was thinking distilled water and baking soda, or do you think that would be overkill?
×
×
  • Create New...