Jump to content
SAU Community

Rb26 Turbo Problem

mina3139

By mina3139,
in Engines & Forced Induction

 Share

Recommended Posts

EdGTR Enthusiast

EdGTR

Posted
Posted

Hey mate alot of people will say different things about turbo failure causing engine damage but i can say 100 percent that on my r32 it happened and it did cause major damage. i have a block with scoring in the last three bores and dents in the piston and head.

if you are a bit mechanical it is somthing you could do at home if you have the time and want to do it. it is a bit involved and does require qiute alot of things to be removed so take your time and label everything or lay it out so it all goes back the same. pics may help.

Good luck

51NNA Community Regular

51NNA

Posted
Posted (edited)

If its a completely stock engine with no aftermarket boost controllers and it hasnt run anymore then 12-13psi then id say its safe but im only going off rb20/25's i honestly dont know about rb26 turbos, from experience ive had an rb20 running 1bar for 3 years without a problem and even sold the turbo too a mate and hes had no problems ither, ive also got an rb25 atm running 1bar and its still going strong after a year, but theres no power to be gained after 14psi, it was a 1kw difference from 14 psi too 18 psi lol, so if your hunting for more power and a peace of mind id change them.

Edited by 51NNA
GTScotT Grand Master

GTScotT

Posted
Posted

more or less a GTR should not have stock turbos on it anymore, they are just too old and the risks are just too high.

you should aim to change your turbos ASAP. however, doing so is one hell of a money pit at the same time.

its much cheaper and easier to own a GTST dollar for dollar a budget build will go a lot further and faster in a GTST

Hadouken Grand Master

Hadouken

Posted
Posted

That guy knows. But at the end of the day, if you want a gtr, you WANT a gtr.

There are people who run standard turbos on 1 bar boost and have done so for a long time. But then you have others who go to crank up the boost and bang, new engine, hello money pit.

It's the same as anything, do you feel lucky? Does the car look in good mechanical condition? Has it been boosted its tits off?

If the car was taken care of through our it's life then you won't have too many problems if you treat her (he if you float that way) right.

Or buy it, change those turbos but expect to pay some cash money to do it. It won't be a cheap endeavor but it will give you peace of mind.

Moodles2 Grand Master

Moodles2

Posted
Posted

R32: normal GTR and V-Spec are ceramic (N1 are steel), R33: ceramic, R34: ceramic

Differences

R32's are 270degree journal bearing

R33's are the same but ball bearing

R34's are the same as R33's but a slightly different turbo design (different compressor housing)

R34 N1's are Garrett -7s which use an inconel wheels (mix of nickel and steel which results in a lighter wheel)

R32/R33 N1's/Nismo's are old laggy 80s tech with steel wheels

Don Dada Mentor

Don Dada

Posted
Posted
R32: normal GTR and V-Spec are ceramic (N1 are steel), R33: ceramic, R34: ceramic Differences R32's are 270degree journal bearing R33's are the same but ball bearing R34's are the same as R33's but a slightly different turbo design (different compressor housing) R34 N1's are Garrett -7s which use an inconel wheels (mix of nickel and steel which results in a lighter wheel) R32/R33 N1's/Nismo's are old laggy 80s tech with steel wheels

Errrrrmmm......NO.

Only R34s are ball bearing.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      Are you an oil nerd?

      By Kinkstaah · Posted

      I think the concept is highlighting the various scenarios where thicker oil helps, and thicker oil potentially doesn't help and only generates heat and costs power, in turn for safety which isn't actually any safer (unless you're going real hot). If anything this does highlight why throwing Castrol 10w-60 for your track days is always a solid, safe bet. 
    • GTSBoy
      Are you an oil nerd?

      By GTSBoy · Posted

      Jason should have shown a real viscosity vs temp chart. All the grades have very little viscosity difference at full operating temperature.
    • dbm7
      BCNR33 Blower Motor Resistor - Testing

      By dbm7 · Posted

      Oops... I meant to include the connector  view... BR/W - power from fuse L/W - motor negative to fan control amp (and off to HVAC pin19) OR/B - PWM signal (from HVAC pin20) B --  ground  
    • Murray_Calavera
      Steps to DIY sanding car back ready for respray....

      By Murray_Calavera · Posted

      Yep, if you are applying filler it sounds like there is something wrong with the body lol. Safe to assume there is going to be a lot of sanding going on if your still applying fillers.  Picture a perfect bare metal panel, smooth as glass. You lay down your primer, it's perfect. (why are you going to sand it?) You lay down the colour and clear, it's perfect. No sanding at all took place and you've got a perfectly finished panel.  You won't be chasing your tail, sounds like you were prepping to start laying filler. If your happy with the body after the sanding, there is some bare metal exposed and some areas with primer, no issues at all, start laying the filler. You are safe to lay filler on bare metal or primer (of course check your technical data sheet as usual for what your filler is happy to adhere to).  This isn't a 100% correct statement. There is primer that is happy to adhere to smooth bare metal. There are fillers that are happy to adhere to smooth bare metal. Just make sure you're using the right materials for the job.  Typically if you are using filler, you would go primer, colour and clear. I've never seen any instances before where someone has laid colour over body filler (maybe this happens, but I haven't seen it before). So your plan sounds pretty normal to me. 
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      I don't think there's any way someone is push starting this car.. I honestly can barely move it, and moving it and steering it is just flat out not possible. I'm sure it is, but needs a bigger man than me. I have a refurbished starter now. The starter man was quite clear and consise showing me how nothing inside a starter really should contribute to slow cranking, and turned out that for the most part... my starter was entirely fine. Still, some of the wear items were replaced and luckily it didn't show any signs of getting too hot, being unfit for use, etc. Which is 'good'. I also noticed the starter definitely sounded different, which is a bit odd considering nothing should have really changed there.... Removed and refit, and we'll pretend one of the manifold bolts didn't fully tighten up and is only "pretty" tight. GM only wants 18ft/lb anyway. I also found a way to properly get my analog wideband reading very slightly leaner than the serial wideband. There's Greg related reasons for this. The serial output is the absolute source of truth, but it is a total asshole to actually stay connected and needs a laptop. The analog input does not, and works with standalone datalogging. Previously the analog input read slightly richer, but if I am aiming at 12.7 I do not want one of the widebands to be saying 12.7 when the source of truth is 13.0. Now the source of truth will be 12.65 and the Analog Wideband will read 12.7. So when I tune to 12.7 it'll be ever so slightly safer. While messing with all of this and idling extensively I can confirm my car seems to restart better while hot now. I did add an old Skyline battery cable between the head and the body though, though now I really realise I should have chosen the frame. Maybe that's a future job. The internet would have you believe that this is caused by bad grounds. In finding out where my grounds actually were I found out the engine bay battery post actually goes to the engine, as well as a seperate one (from the post) to the body of the car. So now there's a third one making the Grounding Triangle which is now a thing. I also from extensive idling have this graph. Temperature (°C) Voltage (V) 85 1.59 80 1.74 75 1.94 70 2.1 65 2.33 60 2.56 55 2.78 50 2.98 45 3.23 40 3.51 35 3.75 30 4.00   Plotted it looks like this. Which is actually... pretty linear? I have not actually put the formula into HPTuners. I will have to re-engage brain and/or re-engage the people who wanted more data to magically do it for me. Tune should be good for the 30th!
×
×
  • Create New...