Jump to content
SAU Community

Recommended Posts

chicken wing thing got me stumped , arm out the window ? Mate of mine just about lost his arm doing this in his VW 55 years ago , pissed :)

I thought it might be the same trannie , you blokes talked me into doing mine :)

They said my motor was finished and I have asked for a photo a couple of times, but nothing in 2 days, maybe bullshit , when they did anything they would send a photo without being asked , so ?

According to the motec datalogging, front diff damage was always done under brakes because the 4WD hadn't let go quick enough

Moral is, if doing hellies, don't stop :D

the good thing is Mick, this cannot happen to me because I do not know what hellies are, what are hellies , sounds like getting the front wheels in the air ?

Hope my Quaife is strong enough :/

Edited by Nismo 3.2ish

That was just to make up my mind what I wanted... And save for it. Lol

I know I know. 20 large ain't gonna just come overnight

I would still have wacked in a temp box in the meantime and enjoy driving the car

I know I know. 20 large ain't gonna just come overnight

I would still have wacked in a temp box in the meantime and enjoy driving the car

I had one. XKLABA gave me one to whack in. However, the car is sitting at my mates old mans workshop getting minor stuff like side skirts and front bar repainted. Unfortunately nothing happens there very fast (been there almost 12 months soon). It's been that long that I almost forget that I own the thing. All good... Will be back on the road soon enough.

Better get your mates Dad to get his finger out, should have your Box soon and driving before Xmas :)

According to the motec datalogging, front diff damage was always done under brakes because the 4WD hadn't let go quick enough



Moral is, if doing hellies, don't stop :D

If your foot is off the throttle and you are braking why would it cause a problem, is it because they were not really built to be a 4WD in the first place ?

I forget the specifics but generally when you jam the brakes on hard trunk g into a corner after a full noise stint and the 4WD is still loaded up the two forces going different ways quite effectively removes the front diff housing, I have seen this happen a couple of times :(

I forget the specifics but generally when you jam the brakes on hard trunk g into a corner after a full noise stint and the 4WD is still loaded up the two forces going different ways quite effectively removes the front diff housing, I have seen this happen a couple of times :(

Is this only if you modify the trannie or with a standard one ?

Sounds like it would go, BANG! :(

I doubt it would ever happen to me as I will not be putting it under those conditions, but would the Quaife front diff make any difference , better , worse or just the same ?

post-52098-0-25734700-1421871196_thumb.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Sag as in the windows start to slowly open themselves, or they're just slow to go up/down with engine off?
    • It looks like it needs a big worm gear drive on it to control the rotating, not a few sloppy pins!
    • As Duncan said, first there was OBD, which few cars used, then came OBD2.   Now an interesting point, OBD2 isn't even for what you want to do. OBD2 is for emissions testing. There is some sensor data on OBD2, but it's up to the manufacturer what they're putting on it. Most scan tools operate on UDS, which like OBD2 is a standard built on-top of CAN. UDS specifies how to structure a message, what very limited things mean such as "read memory address" but it does not specify what is stored in which memory address, that is all up to the manufacturer. You either a scan tool compatible with that vehicle, or to know how to reverse engineer all the data, which can take a VERY long time and a lot of vehicles to get it right. Oh and then the manufacturer does a firmware update and changes what's where... Ask me how I know that as fact Oh, and by the time you've got the scan tool that supports all the manufacturers stuff, well, you're back at "But a consult cable and the Nissan software" The main difference being most manufacturers software these days works with the same hardware readers, as the readers are built to support J2534 which is another standard for how the PC communicates with the tool to make it do specific things on the car...
    • Rotisserie is fully assembled apart from centre connector which obviously isn't required until the car is on it. It packs away fairly neatly and doesn't take up too much room. (Now that I actually have some room after my clean up!) Overall very happy with the quality of it.  Assembly was a piece of piss.  The only thing I didn't like was that the pins that lock the rotation lock wheels in place were a bit of a dick in a bucket scenario. It allowed the arms to rotate a significant amount even when locked in place.  To fix that i measured up the hole and went and grabbed a couple of 18mm fully threaded bolts and a thread tap to suit. I ran the tap through top and bottom so it was threaded both ends.  Then just threaded the bolt through both sides.  It has made a massive difference which hopefully you can tell in the before and after video how much difference it made. 20250207_161431.mp4   20250207_161431.mp4 Hopefully back working on the car over the next few weeks.   20250207_162801.mp4
    • I think my main complaint with your idea is that there is a veneer of idealism spread across it. You want the simple numbers to make it easier, but all they will do is make it easier for someone to come to the wrong conclusion because the fine details will kick them in the nuts. As it is right now, the tiny bit of arithmetic is NOT the obstacle to understanding what will fit and what will not fit. The reality of trying it is what determines whether it will fit. If you had a "standard rule" that R34 GTT guards have that magic 100mm space from the hub face to whichever side you were worried about, and someone said "excellent, this wheel is only 98mm in that direction, I'll just go spend $4k on them and jam them on my sick ride".....they would just as likely find out that the "standard rule" is not true because the rear subframe is offset to one side by a fairly typical (but variable) 8mm on their car and they only have 92mm on one side and 108 on the other.
×
×
  • Create New...