Jump to content
SAU Community

Piglet's Rebuild Of His Busted Tomei 2.8


Recommended Posts

This thread is like a whore thread haha... Excuse the pun :D

It better be ready tomorrow. Itching to drive it! I know they will finish the tune on 98... Better bring some E85 with me and turn the boost controller nob to the right!!!!

Link to comment
Share on other sites

So i try to ring you, you never answer me anymore, i text, you ignore. I send nekked pictures, you seem to reply immediately and want more.........do you still love me paul?

Link to comment
Share on other sites

So the real question is when are you going to take the car off the road for anothe r6 months to swap over to a single?

I sold the single to a mate. I can't be bothered with that. I don't think I need anymore grunt!

Unless you wanna sponsor me mate ?

Link to comment
Share on other sites

with your brawn and my incredible wit, good looks and knowledge base, we could rob a nando's of thier chicken, then sell it on the black market at a slightly reduced price. After we have achieved this goal, we can invest heavily in metal exploration ventures in western australias mineral rich north west and profit hugely as we will be running a post office box company system linked to an offshore bank account to avoid tax, all whilst sipping boutique piss on a beach in the maldives with nekked women answering our every call.

i need another bourbon

Link to comment
Share on other sites

Had my first little drive today, although in RWD. Total fkn waste of time. Anything more than 30% throttle and above 3500 RPM it was fry time. Didn't try it in 4th but the first 3 gear were fkn useless!

Looks like I have found a Non V spec rear diff housing too. Get that bloody rear diff in! Wahoo!

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Harness update time have had great fun and learnt so much already so far with this project. I started off making both the ignition and injector sub harnesses in the hope any mistakes i made here aren't as hard to undo and learn from as the main harness.  A cool comparison of the old harness using presumably TXL wire and the new which is using Tezel. Also opted to use DTM plugs to keep the whole setup as neat and tidy as possible and tucked the wiring under the coil bracket to try and keep it all from sticking out too much. Although the injector harness, I'm not overly happy with as I'm still using the rubber boots that are supplied with the type of plugs it just looks ugly and sticks out like a sore thumb with the white identifiers so a slight redesign may be done.   Then it was main harness time and most importantly trying to route it nice and away from the heat it will use the OEM heater hose routing which is no longer present to keep the harness up high and secure. it's amazing how much smaller this harness is able to be compared to the old one. plugged everything into the emtron and with the help of the tuner again attempted to start it up and instantly fired up and running smoothly on all 6 which was a big shock to myself. So still some routing and adjusting to be done for the final fit up and installing a knock sensor harness plug which is in the post all has gone surprisingly well.     The old harness for shits and giggles.
    • They do that at random every now and then, with almost no detectable cause. Mine has done it a couple of times (over 25 years!!). Never worked out why.
    • I don't post on here and have been lurking for some time now. Many of the topics have helped me out more times than i can count. I was racing yesterday (11/9) and blew a front right CV shaft. I have spares so I popped a new one in. A thread i read previously said to check the engine mounts if you blow a front CV. Upon inspection, the front right mount was completely separated from the upper plate. This discovery saved me time and money, because i would have blown another CV if i went back out. Just wanted to thank you guys and wish everyone luck with with their builds. (Now if we could only come up with a solution for my power steering belt flying off after hitting the rev limiter, lol)
    • Either way he still need those style of spacer to go into the manifold because the photo he currently has is not going to work 
    • You can just get the injector bosses, which allows top feeds to fit. He can use the same injectors without issue, like these (another option): https://rocketindustries.com.au/af59-2210-rb25-fuel-injector-inserts     The Racework ones look a bit better: https://www.nzefi.com/product/raceworks-lower-injector-mounting-boss-kit-for-r33-rb25det-s14-s15-sr20det/   You could also just get a similar kit like the Radium one by Plazmaman: https://plazmaman.com/product/nissan-rb25det-r33-billet-fuel-rail/?srsltid=AfmBOoogfYq49X0fu2Wdbf8yOf6zt9egyPAif_gn3Qr3G8hzAphhTgOkO70  
×
×
  • Create New...