Jump to content
SAU Community

R32 Gtr Track Car Build Terminated

adam Foster
 Share

Recommended Posts

adam Foster Mentor

adam Foster

Posted
Posted

Hi all so I have been collecting part for a while to build a track gtr my daily (trd aurion) has decided to pack its lunch and need a new motor.

To come up with the cash thee bellow is for sale.

1992 r 32 gtr shell. Limited interior only dash, 320km cluster, center console etc.

Has circuit spec coil overs, adjustable camber, tie rods etc front and back white line sway bars good standard diff. G4 racing 8 pot front brakes 330mm 2 piece rotors. Standard rear brakes but no rotors.full 4ws removed along with the abs.. Brake line re done.

Rolling shell on sparco racing wheels $5500

Buddy club P1 racing wheels 17 by 9 in good condition $1250

Link/ Vipec ecu with electronics boost controller $1500

Rb26 with leman nismo turbos rear housing have just been ceramic coated. Aftermarket low mount manifolds with external waste gate and stainless dump pipes all just been ceramic coated.

Spitfire coil packs, one of the older stron n1 oil pumps. New triple layer head gasket just been put on. Tommie sump baffle. And standard rb26 gearbox $5000

Got heaps of spares and bits and pieces

Contact 0411672105.

Location morisset

Link to comment
https://www.sau.com.au/forums/topic/397903-r32-gtr-track-car-build-terminated/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Haggerty
      RB25DE NEO with Haltech ECU

      By Haggerty · Posted

      Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • brillo
      Leak from Tokico BM50 Brake Master Cylinder

      By brillo · Posted

      Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • MBS206
      Cas issue

      By MBS206 · Posted

      It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • nash47
      Cas issue

      By nash47 · Posted

      Yes sir am asking is there possible way from aem tuner from wiring pins 
    • MBS206
      Cas issue

      By MBS206 · Posted

      Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...