Jump to content
SAU Community

Rb25 Gcg Hiflowd Turbo With 14Psi Actuator

Tim805
 Share

Recommended Posts

Tim805 Contributor

Tim805

Posted
Posted

for sale is my mate jasons rb25 GCG hiflowed turbo with a 14psi wastegate actuator made 256kw atw on a rb20 running 22psi. only run for 2 weeks before he crashed his car.. sad day car was awesome with turbo set up.. cost $2200 sell $1650 ono.. contact jason on 0405912939.. post-61261-0-11766300-1335079031_thumb.jpg

video is off a earlier run phone went dead photo of dyno sheet to prove above

Tim805 Contributor

Tim805

Posted
  • Author
Posted

yeh stock internals just a absolute genius tuner.. can contact herman at envy imports and dyno for proof..02 9907 4144.. or even to get a shit load of power out of your own car...

TTT Grand Master

TTT

Posted
Posted

Hey mate.

these turbos were the bees knees of hiflows years ago.

But have you seen what else is available these days?

and what sort of money they are worth BRAND NEW?

If you/your mate want to sell a used hiflow turbo, it's gotta be a better deal than the likes of Hypergear range.

Tim805 Contributor

Tim805

Posted
  • Author
Posted

ill get a pic off jason of the whole dyno sheet asap... TTT did you see the dyno sheet this shit must be the bees knees cause it works .. proof is there to be seen.. not arguing that there arent other great products out there but this works power is there cost is paid and savings to buyer to be had.. if ya interested make jason a offer contact him on 0405912939..

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • soviet_merlin
      Magnetic Drain Plug Snapped in Half

      By soviet_merlin · Posted

      Half anticipating the next question then: I have two magnets stuck in my oil pan. What should I do? 
    • joshuaho96
      Magnetic Drain Plug Snapped in Half

      By joshuaho96 · Posted

      If it's magnetic what is stopping you from using a magnet on a thin wire from fishing it out?
    • dbm7
      Shifting questions

      By dbm7 · Posted

      Those 2 solenoids in that assembly I mention, are the PWM solenoids for torque converter lock-up clutch & EPC (line pressure control) ~ when most folks hear of 'solenoid failure', the tendency is to think electrical failure...but fact of the matter is, especially wrt the EPC solenoid (which is moving/running all the time), you can have an electrically 'good' solenoid, that's absolutely broken/worn out mechanically inside...ie; valve plunger return spring rubbing against spring retainer plate, lowering preload pressure.. ...and the solenoid armature extension limit spring wafer with bad wear/broken off petals... ...and if there's ever been any metal flying about, damage to the valve plunger end itself... ...the stuff one never really sees, unless you go the whole 10yards trying to answer the question "why is my line pressure screwy, but TCU isn't flagging any EPC solenoid fault?"...and carefully dissect the solenoid. Worst (and most probable) scenario is when the plate spring petals break off, they get held by the magnetic flux, get mashed up by the armature into little bits, which end up in the space between the armature & shading core bore, and things get stuck or randomly jam up, and your line pressure goes flat and doesn't change...and the TCU never sees it, as it doesn't actively monitor LP... ..then it gets into insidious land, if you end up with lower than expected line pressure...lets say high clutch..and the lower pressure causes it to slip ~ when I say 'slip', think say 2000rpm on the drive plates, and 1800rpm on the driven plates, because the slip is making them under-rotate by 200rpm ; you get all the usual nasties like heat and band/clutch wear, but even if it's only 20rpm slip the same thing happens...and... you'll hardly ever pick this up driving the thing with the torque converter active as it effectively masks these sorts of slippages that are line pressure related ...(the newer TCUs can detect clutch slip rate)...just  FYI as it were...  
    • GTSBoy
      MAJOR FUEL ISSUES 25det neo r32

      By GTSBoy · Posted

      There's nothing that some paddle pop sticks and extra cable ties can't fix.
    • QB6SAGR
      RB20 in need of modest love injection

      By QB6SAGR · Posted

      Hey guys, so Golebys has good prices on Bosch injectors, and also sell an adaptor to go from 1/2 length injector to standard with the Nissan 10.5mm top seal.  Does anyone know if that adaptor is to suit the 14mm or 11mm injector tops?  And re. The bottom seal, to suit my standard RB20 intake, would I be right in saying I can just slip the 14mm square section O ring over the bottom of the new injector and done? Thanks in advance guy, Cheers, Rowdy
×
×
  • Create New...