Jump to content
SAU Community

Recommended Posts

  • Replies 151
  • Created
  • Last Reply

Top Posters In This Topic

  • 4 weeks later...

Bump

New parts:

Mazda Air temp sensor (for PowerFC D-Jetro) (brand new) $120

S14a HKB boss kit with airbag light cancel resistor plug (brand new) $180

S14 'Edge' Side skirts, unpainted white gelcoat (brand new) $250

S14.5 Origin +25mm conversion fenders (brand new) $450

S14 Origin +50mm rear fenders (brand new) $450

S14 light weight fibreglass doors (brand new) $900

S14 Full Lexan window kit (rear window with NACA vents, rear quarters, driver and passenger door windows with slider window kits) (brand new) $1,050

S14 Nismo Super Coppermix TWIN PLATE clutch rated to 670hp, one of the best SR clutches available (brand new) $2,100

used parts:

Greddy engine oil cap $40

S14/S15 Nismo springs and struts (lower than factory, very comfortable on street) $550

S15 factory rear boot spoler with led's, pewter colour $120

S15 JDM factory steering wheel with airbag $250

S15 Hybrid aluminium radiator $250

S15 Stage21 aero front bar (painted blue) $350

S15 boot lid and ducktail spoiler (not separating, duck tail is sikaflex'd and bolted on to boot lid) $300

S15 Alcon front brake kit, monoblock aluminium 4-pot calipers (weigh less than stock calipers!), 335mm 2-piece rotors, Ferrodo DS2500 pads $3200 (new price from PWR is $4300)

S13/180sx TRUST 19 row oil cooler kit, thick quality trust core, for S13/180sx with filter relocator $700

C-west genuine carbon fibre GT-wing, mounted on S15 boot lid, wrapped in matte black vinyl $1,100

Hypertune SR20 low port intake plenum (small dent at one end) + 77mm Hypertune throttle body $1,750 (Hi Octane Direct sell the plenum alone for $1800+ and $600 for the throttle body).. save over $800 off new prices

HKS Super Sequential SQV BOV, genuine HKS, mounted on evo 8/9 hot pipe $300

STACK 8130 dash with sensors and loom $1,800

ATP 'Frank' turbo, with stainless steel manifold, will fit s14/15 SR20det, good for around 240-250rwkw with stock cams. Braided lines included. $1100ono

R34 GTR Cusco Type-40 aluminium strut tower brace $240

R34 GTR C-west N1 front bar (genuine), carbon fibre (painted black), will need respray/minor repairs $750

R34 GTR C-west carbon fibre cannards for N1 bar $350

R34 GTR Nismo dash cluster (black version) (brand new) $700

R34 GTR/GTT Nismo GT LED tail lights $1,200

4x Advan AD08 265/35/18 tyres 99% tread (almost new, less than 300km) travelled $1300

RAYS Nismo LMGT4's white 17 x 9 +22 all round, no tyres, concave spokes, clears GTR brembo and Alcon brakes to 335mm rotor $2,200 firm

RAYS Nismo LMGT4's bronze 18 x 9 +22 all round with Advan v103 sport tyres about 50% tread, concave spokes $2,800

RAYS LE37's Top Secret Limited Edition Gold 18 x 10.5 +15 all round (rare, don't really want to sell these) $4000

SSR Type-C 17 x 9.5 +15 PAIR ONLY, white, average condition for age, no buckles $1100

** can post wheels interstate if needed at buyers cost **

still for sale!

New parts:

Mazda Air temp sensor (for PowerFC D-Jetro) (brand new) $120

S14a HKB boss kit with airbag light cancel resistor plug (brand new) $180

S14 'Edge' Side skirts, unpainted white gelcoat (brand new) $250

S14.5 Origin +25mm conversion fenders (brand new) $450

S14 Origin +50mm rear fenders (brand new) $450

S14 light weight fibreglass doors (brand new) $900

S14 Full Lexan window kit (rear window with NACA vents, rear quarters, driver and passenger door windows with slider window kits) (brand new) $1,050

S14 Nismo Super Coppermix TWIN PLATE clutch rated to 670hp, one of the best SR clutches available (brand new) $2,100

used parts:

Greddy engine oil cap $40

S14/S15 Nismo springs and struts (lower than factory, very comfortable on street) $550

S15 factory rear boot spoler with led's, pewter colour $120

S15 JDM factory steering wheel with airbag $250

S15 Hybrid aluminium radiator $250

S15 Stage21 aero front bar (painted blue) $350

S15 boot lid and ducktail spoiler (not separating, duck tail is sikaflex'd and bolted on to boot lid) $300

S15 Alcon front brake kit, monoblock aluminium 4-pot calipers (weigh less than stock calipers!), 335mm 2-piece rotors, Ferrodo DS2500 pads $3200 (new price from PWR is $4300)

S13/180sx TRUST 19 row oil cooler kit, thick quality trust core, for S13/180sx with filter relocator $700

C-west genuine carbon fibre GT-wing, mounted on S15 boot lid, wrapped in matte black vinyl $1,100

Hypertune SR20 low port intake plenum (small dent at one end) + 77mm Hypertune throttle body $1,750 (Hi Octane Direct sell the plenum alone for $1800+ and $600 for the throttle body).. save over $800 off new prices

HKS Super Sequential SQV BOV, genuine HKS, mounted on evo 8/9 hot pipe $300

STACK 8130 dash with sensors and loom $1,800

ATP 'Frank' turbo, with stainless steel manifold, will fit s14/15 SR20det, good for around 240-250rwkw with stock cams. Braided lines included. $1100ono

R34 GTR Cusco Type-40 aluminium strut tower brace $240

R34 GTR C-west N1 front bar (genuine), carbon fibre (painted black), will need respray/minor repairs $750

R34 GTR C-west carbon fibre cannards for N1 bar $350

R34 GTR Nismo dash cluster (black version) (brand new) $700 sold

R34 GTR/GTT Nismo GT LED tail lights $1,200

4x Advan AD08 265/35/18 tyres 99% tread (almost new, less than 300km) travelled $1300

RAYS Nismo LMGT4's white 17 x 9 +22 all round, no tyres, concave spokes, clears GTR brembo and Alcon brakes to 335mm rotor $2,200 firm

RAYS Nismo LMGT4's bronze 18 x 9 +22 all round with Advan v103 sport tyres about 50% tread, concave spokes $2,800

RAYS LE37's Top Secret Limited Edition Gold 18 x 10.5 +15 all round (rare, don't really want to sell these) $4000

SSR Type-C 17 x 9.5 +15 PAIR ONLY, white, average condition for age, no buckles $1100

** can post wheels interstate if needed at buyers cost **

bump!!!!! Rawwwrr.. buy my shit!

SimonR32 sent you a pm buddy. Not really keen to send interstate, i don't have time to arrange the freight etc. Let me know

Hahaha. Indeed.. But try dealing with 500 low ballers then you may understand the frustration that comes with selling parts on forums.. not so much SAU, but always on nissan silvia.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • It was roughly 3.5 hours.    car went in around 11:00 and I was done around 2:30 He did the initial runs, install the BC and then Nistune install and tune.  The best part was sitting in the lobby and hearing the skyline on full throttle at the dyno 😂😂
    • Glad it all went smooth. How long did the tuning process take?
    • Yeah that was kind of the same feedback my tuner gave me.  the boost tee is until I can sort out my plan for the electronic boost controller and what I’d get, where I’d mount the dash etc.  I’m happy with this until I can figure it out. Not a big fan of the A-pillar gauges. I’d like to get a clean install of the boost gauge - something digital like GFB.  Something like that might fit neatly where the ashtray is and look clean. I feel like replacing the OEM triple gauge is a bit extreme for a weekender like my skyline. And it’s not making crazy power to need all the additional sensors/gauges. 
    • I'm about to swap my box to Tremec T56 Magnum F & initially thinking of re-using my DCS twin plate (can get it re centred for the bigger spline) but it's been called out the box will be noisy (rattle) as the clutch is unsprung.  So I'm doing as much research as possible. I'm not so worried about holding the power as I'll go the track version which on paper will hold the maybe 1000hp I make. It's the longevity I worry about. DCS told me they don't use a sprung centre as it's just something that can break. The uni clutch has a very complicated sprung centre. Any one had or heard about any issues with it failing? Thanks in advance.
    • Auto is at least 10% (from my real, actual experience with different torque converters and manual on the same setup) ~185rwkw at 11.6psi (peak!) is entirely what one would expect without a FMIC or anything else on the intake, it does bleed off towards the higher RPM so it's what, 9psi there? Note: There is nothing that can be done about this with a manual boost tee. If you want to hold it steady and gain more top end, well - You will need electronic boost control.....
×
×
  • Create New...