Jump to content
SAU Community

Wheels Width And Offset For R33 Gtst S1

J-Salad
 Share

Recommended Posts

J-Salad Contributor

J-Salad

Posted
Posted

Hey guys, sorry if this have been covered for so many time. i just wanna know what width and offset i should get if i want the wheels to slightly stick out of my guards, like the 350z in the photo. Cheers!

PS. I am thinking of getting 18X9.5 all around with 263/35 tyres and i don't want to use spacers to fit the wheels on my car.

post-85265-0-28210500-1336188373_thumb.jpg

Link to comment
Share on other sites
DarkRyda Proficient

DarkRyda

Posted
Posted

Doesn't require spacers front and rear,, you will however need to roll your guards on all 4 sides should cost $200-300. The rim design however factor in but it should still stick out nicely.

Link to comment
Share on other sites
Hank Scorpio Grand Master

Hank Scorpio

Posted
Posted

18x9.5+20 will stick out nicely

5748249445_95fd49eb0c_b.jpg

They're not 265's though surely!

You are going to struggle to put a 265/35R18 on the front of a RWD GTS-T I would have thought :wacko:

18x9.5's all around will go no dramas but I am an advocate of 225/40R18 all round or 225/40 255/35 staggered set-up.

Link to comment
Share on other sites
Husky33 Veteran

Husky33

Posted
Posted

I have 18x9.5 +22's with 265/35's all round on my r33 gtst.

Need a guard roll and modify the splash guards up front.

Actually got 7mm spacers on the back aswell, just clear.

Shit pic but yeah:

post-3412-0-89672900-1336389483_thumb.jpg

Link to comment
Share on other sites
J-Salad Contributor

J-Salad

Posted
  • Author
Posted

I have 18x9.5 +22's with 265/35's all round on my r33 gtst.

Need a guard roll and modify the splash guards up front.

Actually got 7mm spacers on the back aswell, just clear.

Shit pic but yeah:

So do you mean that i need 7mm spacers on the back to clear the breaks? Plus, will your ride height be legal in SA? Cheers!

Sorry for asking so many questions! :(

Link to comment
Share on other sites
Husky33 Veteran

Husky33

Posted
Posted

Don't need spacers, just put them on because i had the space to push them out a bit further. In other words i could have gone +15 offset on the rear.

Unless the wheels have ALOT of dish, they should clear the brakes no dramas in a +22 offset.

My ride height is around 100mm give or take at the exhaust under the car

Link to comment
Share on other sites
Jap_star Mentor

Jap_star

Posted
Posted

whats the camber set up. surely around the -3 for that. My 9 +22 with -.2 camber is about 5mm out the guards. however when camber was at -1.5 i was able to slide a 8mm to make it almost sit the same

Link to comment
Share on other sites
Serpandrew Rising Star

Serpandrew

Posted
Posted

I have 18x9.5 +22's with 265/35's all round on my r33 gtst.

Need a guard roll and modify the splash guards up front.

Actually got 7mm spacers on the back aswell, just clear.

Shit pic but yeah:

Are those TE37's?

The red spoke makes me think so :worship:

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Leigh_Mack
      Hello, Newbie, anyone know my 32's history?

      By Leigh_Mack · Posted

      Hello,new to the group, I bought a R32 from auction recently, wondering if anyone knows the cars history, seems to have the usual go fast bits on it, plan is to do an engine swap- add 2 extra cylinders and 1 extra turbo. https://www.dropbox.com/scl/fi/i4rjmlzubjbwjtguh6f4s/IMG20241011140744.jpg?rlkey=q0lumm251377vknbqktfwrycq&st=7scvwx4e&dl=0 https://www.dropbox.com/scl/fi/ro24qmwzlczzlfsr4y05x/Screenshot_2024-10-10-10-49-23-90_9a2f5bb2149dae94cd1e190effc09b33.jpg?rlkey=oyguh26ttshlf04ccp48odf4v&st=xloae97b&dl=0   New to forums and posting pics, if links don't work, take it easy on me, 42yrs old and I tune carburettors!!  
    • sonicii
      2020 Nissan Skyline 400R V37/Infiniti Q50 RS insurance in NSW

      By sonicii · Posted

      As far as I know, Infiniti stopped importing vehicles before 2020, even though they were still selling their stock for at least a year or 2 after that, they were older build years, therefore, you can import a 2020 400R, because you couldn't buy an AuDM 2020 built Q50 RS. As for insurance, you might need to go through one of the enthusiast insurance companies, they tend to insure a lot more grey import models than the mainstream insurers as Duncan mentioned.
    • araiko
      Importing from the US into W.A - 15 yo old car

      By araiko · Posted

      loved seeing the zenvo on the a1 just after the hatfield tunnel i was the guy in the white van trying to egg you on it sounded awesome and those exhausts glowing red inside insane cheers for the thumbs up tim and tom.
    • DraftySquash
      Question about R34 GTT A/T Solenoids

      By DraftySquash · Posted

      So.... when I'm finally getting around to having my power steering leak sorted, now it looks like I've got the same issue most A/T Skylines are having. My A/T light will randomly come on and I'm stuck in 3rd gear until I turn the car off and on again. Only 3 weeks ago I did a complete transmission service: Oil flush + new gasket + new filter. This came out of nowhere!! It wasn't like the car was driven hard. I drove about 3 mins down the road to get fuel and boom!!!  Anyway, I have a few questions and hope you fine people can help me out here. All questions are in red. 1. The solenoids: I was looking at the parts catalogue in Amayama and I could only find the Solenoids as an assembly. https://www.amayama.com/en/part/nissan/319404ax05 I read in another thread that Solenoid A = 31940-4AX02 & Solenoid B = 31940-4AX05 but the Amayama product has only the code of B. Is this the right part? Can anyone who has done the Solenoid changes or seen them confirm if this is the complete set of A & B?   2. Gasket and Filter: I'm not going to try change the solenoids myself because it seems difficult to do in a home garage with just 2 jack stands. I plan to take it to a shop and get it changed. I was also going to buy the transmission sump gasket at the same time so I don't reuse the same gasket. Should I just use the existing gasket as it has only been on the car since OCT 19th? (~3 weeks) Should I be buying a brand-new gasket and a filter? Does this job involve taking the filter out?   Thanks in advance to everyone. It's hard to find a video of someone doing a solenoid change on a R34 so any help you can give answering my remaining questions would make me less stressed.
    • Kinkstaah
      R34 GTT RB rough idle problem with weird RPM gauge fluctuations

      By Kinkstaah · Posted

      Yea - From what I have seen from the video, the car idles like any R34 lol 50PSI of fuel pressure is hardly super abnormal, the regulator is working because the pressure remains static when the throttle gets revved, i.e pressure remains the same when manifold vaccuum changes. Bigger pumps on stock rails always bumped the pressure in the rail without using an aftermarket regulator to change that. Do you know what your IAC is actually doing? Has there been any data showing the stepper motor % etc? There's no way your idle is actually moving around the way the cluster(s) are indicating. You would hear the difference with the engine RPM flying to 3k and 1k in mere seconds. I'd be checking the wiring to the tacho. What the tacho is telling you and what the engine/ecu is telling you are different things. I assume your ECU doesn't display the spike. So whatever is telling the tacho to be at X rpm is doing something weird. When the going gets insane, you're on the wrong path. You've ruled out plenty of things that are working correctly/aren't the issue. Your idle isn't doing what the tacho is indicating. You have two seperate issues, I don't think they are linked, and the idle seems reasonably okay unless it's stalling which.. well, it hasn't. Troubleshoot the stall if it occurs by figuring out what your IAC is doing vs what it is being told to do.
×
×
  • Create New...