Jump to content
SAU Community

Recommended Posts

So I have an R34 GTT with many mods: Apexi PFC w/ commander/datalogit, GReddy Profec Type S EBC, GReddy Intake manifold and fuel rail, RC 1000cc injectors, Massive Precision Turbo, Tial WG, FMIC, HKS SSQV, Aeromotive FPR, AEM Wideband, 3" Turbo-back Apexi exhaust, NGK BKR7ES-11's regapped at .030.

On to my problem......

I've had the car now for about a month and a half and have been constantly working out the bugs. First was a new center section for the turbo due to an apparently recent rebuild that didn't include a thorough hot tanking and left bits of metal shavings in the oil feed line that led to blown seals and bearings. Fortunately it doesn't seem to have harmed any other parts of the engine yet, I have ran several quarts of oil through in an effort to remove the machining leftovers. Next came proper PCV/ catch can installation and hose routing seeing as how it only had valve cover breather filters and an unhooked PCV valve, as well as an un-plumbed AAC valve that was sucking in unmetered air. Also replaced the O2 sensor and saw a dramatic increase in fuel mileage as AFR's.

However, once all of these things were replaced and repaired I noticed that the car did not want to pull as hard as before and that even though the idle was more stable at 1000-1100rpms it did not want to stay running if I let it idle for too long. And as of now the car won't start at all. I've checked all of the usual suspects: AFM, New plugs AGAIN, no vac leaks, fuel pump is working great and have great fuel pressure. I am thinking it is my CAS, but not sure because if I take it out and spin it I can hear the fuel pump run and the injectors clicking. BUT when watching the FC Commander it only shows the car getting 4-7 degrees of timing under cranking. As well as when hooked up to Datalogit it wants to sit at 6000 load cell also while cranking. Im not sure why it is not getting more ignition timing while I am cranking it. My tuner is even scratching his head as to why the car won't start. Im guessing part of it is due to not being able to see the start up cranking ignition tables on the Datalogit screen and even by altering the whole map to 40 degrees it still only read 4-7 on the commander!?! Oh and the boost control kit setting is turned off as well as I have re-initialized the Com twice and re-loaded the map to no avail. Sorry for my super long first post on the site, but I am at my wits end on this one and USA forum support is a little lacking when it comes to this one. . Any help would be greatly appreciated!

Thanks!

Link to comment
https://www.sau.com.au/forums/topic/399439-power-fc-ignition-timing-issue/
Share on other sites

  • Replies 51
  • Created
  • Last Reply

Top Posters In This Topic

Unfortunately I don't have the factory ECU. A far as the rpm's the Datalogit only registers the cranking rpm's to be reaching around the 250-300 mark. But while cranking it, it says in the monitor screen the load sits at 6000 and timing dumps at 7 degrees max. Im thinking some sensor has failed or shorted. Thanks for the response btw! I knew SAU would come through for me!

I know a guy that recently had ignition problems with power fc, although was ithrough rev range not start up, after numerous replacements of parts changed the ecu and problem solved, see if you can get hold of another ecu as guilt toy recommends to try, maybe the tuner has something around for a start up test?

I have replaced the spark plugs numerous times with no noticeable change. I am going to check for weak spark next. It tries to start occasionally but thats only when i get the max timing of 7 degrees. My wife drives a 33 also with a PFC. Similar mods but way different map, maf, injectors, etc. But im not sure if hers has been converted to a S2 engjne. It is basically set up almost identical as mine as far as the coils not having an igniter and hers has the apexi boost control kit. It would be nice to see if it works though. Im really hoping my ECU hasnt taken a dump on me.

The lower timing whilst cranking is normal and needed, when your cranking the motors only doing 200-300rpm so the piston isnt moving up and down very fast at all, therefore you dont need much timing to get the burn happening around TDC. What does injector duty look like whilst cranking?

Yeah I am pretty sure her plug is different than mine. I just rechecked spark and all are seeming very strong. I also disassembled the CAS and everything looks normal in there as well. I reassembled and still same scenario. I was teased a little when I tried to start for the first time today, b/c I noticed on the Commander that the timing jumped up to 22-30 and then it stalled again only to return to previous results. I haven't checked injector duty yet. Im starting to lean towards a sensor of some type, maybe still the CAS. Will a 95 Z32 CAS work? They have the same style plug and housing. Not sure if it needs re-pinning though. I did notice the part of Paul's FAQ about fake Z32 MAFs and noticed that mine matched the description, fortunately I had an extra known working one and installed that out of precaution, no change still. Has anyone ever encountered the "6000" load problem when watching data stream monitor on the Datalogit on the lower left of data stream window, to the left of the Timing parameter box?

The plugs are definitely wet and black. I had to change them after my continuous diagnostic cranking attempts. Injector duty is 0.3% while cranking. I did a little numbers checking with the wifes car. During cranking the timing does seem to match mine but her injector duty starts at 0.3% and then increases to 0.7-1.0% as it fires up. I am going to pull out my injectors for kicks and see if they are clogged up. But the duty seems a little low. Am I wrong on this assumption?

Check the cam timing if u havent already.

If the plugs are really wet but there is spark. Try trimming the injector percentage and see if u can get it to start.

Check all piping, check afm setting in power fc,

I wouldn't be concerned with that load value as it probably won't be using that for any kind of load detecting at crank. That duty cycle is probably right for cold crank with standard injectors - not 1000cc injectors. At a 300rpm (crank) allowable inj on time is 120/300 x 1000 = 400ms so at .3% dc injector on time is about 12ms which is quite a lot of fuel for crank.

I would try halving your cranking ms table. I often see "tuners" miss these tables when injectors are changed.

Yer try a little less fuel.

Also, before you even consider swapping the cas get a timing light on it, it sounds like the cas is fine and a timing light will confirm that.

Back to basics really, if its got spark it can only be fuel, timing (cam or or ignition) or a f**ked motor (very unlikely).

I checked cam timing last night and it's on but I think it may have jumped time on the crank. It was about 6 teeth away on the cams from being lined up so I tried to turning it counter-clockwise just a bit and noticed the crank bolt wasnt very tight. It basically loosened up when i tried to turn it. So i stopped and went clockwise to tighten it back up to line the cams up. Im going to take off the lower cover and check the crank marks too. I dont think it slipped very much if any but i need that piece of mind. Once I know every thing is lined up i will do a compression test.

I wouldn't be concerned with that load value as it probably won't be using that for any kind of load detecting at crank. That duty cycle is probably right for cold crank with standard injectors - not 1000cc injectors. At a 300rpm (crank) allowable inj on time is 120/300 x 1000 = 400ms so at .3% dc injector on time is about 12ms which is quite a lot of fuel for crank.

I would try halving your cranking ms table. I often see "tuners" miss these tables when injectors are changed.

Doesnt the pfc cater for this when you re-scale the inj table?

OP....Is the inj correction/latency table set up, and proper afm selected?

Edited by Don Dada

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Major thread necro but how bad of a job is it to DIY? Looking at it online it looks like if you reuse your ring and pinion as long as those are in good condition it should be fine to just pull the axles/front cover and replace the diff that way? Or should I be replacing everything and doing preload measurements/gear mesh testing like the factory service manual mentions for the rear diff?
    • in my list I had the R33 GTR as the best Skyline. Infact I had all GTR's (33>34=32), the NSX, the GTO, the 300ZX, the 180SX, the S15 better than the FD RX7. I had the MR2 and the A80 as 'just' better. I also think the DC5R Integra looks better but this is an 01 onwards car. I also think the FC>FD. It's almost like aesthetics are individual! The elements @GTSBoy likes about the FD and dislikes about the 180 are inverse in my eyes. I hate the rear end of the FD and it's weird tail lights that are bulbous and remind me of early hyundai excels. They are not striking, nor iconic, nor retro cool. The GTO has supercar proportions. I maintain these look much better in person (like the NSX) especially with nice wheels and suspension which is mandatory for all cars pretty much. Some (or all) of these you have to see in person to appreciate. You can't write a car off until you see one in the flesh IMO. Like most people we probably just like/dislike cars which represent certain eras of design or design styles in general. I also think the 60's Jag E type looks HORRIBLE, literally disgusting, and the 2000GT is nothing to write home about. FWIW I don't think the Dodge Viper Gen1's have aged very well either. You can probably see where I rate bubbly coupes like the FD. I know we're straying now but the C4 and C5 absolutely murder the Viper in the looks department as time goes on, for my eyes. Wouldn't surprise me if people who love the FD, also love the MX5, Dodge Viper, Jag E Type, etc etc.
    • I used to hate R31s, and any of the other Nissans that led up to it, and any of the Toyotas with similar styling, because of the boxiness. They were, and remain, childish, simplistic, and generally awful. I appreciate R31s a lot more now, but only the JDM 2 door. The ADM 4 door (and any other 4 door, even if they are unique compared to our local one) can eat a bowl of dicks. The Aussie R31 is also forever tarnished by their association with stereotypical bong clutching Aussie R31 owners of the 90s and early 2000s. I think the Nissans of the 70s (other than 120Y/180B/200B) are far superior looking to the 80s cars. The 240K era Skylines are boss. The same is broadly true of Toyotas. Hondas don't ever register in my thinking, from any era. Mitsus are all horrid shitboxen in any era, and so also don't register. Subarus are always awful, ditto. Daihatsus and Suzukis also don't generally register. They are all invisible. I think the SW20 MR2 looks fiddly. The 3000GT/GTO is like that but way worse. Too many silly plastic barnacles and fiddly gimmicks ruined what could have been a really nice base shape. Kinda-sorta looks like a big heavy ST165 Celica coupe (and I'm not sure if that's a good thing or a bad thing). I think the 180SX is dreadfully bland. It's not bad looking. But it has no excitement to it at all. It's just a liftback coupe thing with no interest in its lines, and bad graphical elements (ie wide expanses of taillight plastic on the rear garnish). The S13 Silvia is a little better - getting closer to R32 shapes. But still....bland. S14? Nope. Don't love it. S15...a little better. Probably a lot better, actually. Benefits from not being like a shrunk in the wash R34 (where the S13 was a shrunk in the wash R32 and the S14 looked like a Pulsar or something else from the stable on Nissan mid 90s horrors). The Z32 was hot as f**k when it came out but hasn't aged as well as the A80. Keep in mind that I think the R33 is the most disgusting looking thing - and out of all the previous cars mentioned is objectively closest to my precious R32. It's just....real bad, almost everywhere you look. And that is down to the majority of what was designed in the 90s being shit. All Nissans from that era look like shit. Most other brands ditto. In that context, the FD absolutely stands out as being by far the best looking car, for reasons already discussed. Going behind the aesthetics, the suspension alone makes it better than almost any other car.  
    • If they just called it the "Mazda Tiffany", it would have been spot on.
    • Yup but for me its the HR ! Cut my teeth on the old holden 6s in the day ! And here's me thinking in the day it was also the 300ZX and the Mitsubishi GT3000 ! All, as well had good lines, but always seemed to need finishing off, style wise.
×
×
  • Create New...