Jump to content
SAU Community

Need 5 Stud Conversion For My 32 Qld

Na boy

By Na boy,
in Wanted to Buy

 Share

Recommended Posts

N-DAWG Mentor

N-DAWG

Posted
Posted

Got 5 Stud Hubs/Upright Assembly from an R34 GTT Front Cut (114,000kms) if that's suitable. No Calipers unfortunately.

Located in Wollongong NSW 2500.

Postage arranged and paid by you, ideally by courier due to size and weight.

2011-11-11174323.jpg

2011-11-11174317.jpg

Also have these bits if you need them as part of your conversion:

th_2011-11-11174749.jpg

th_2011-11-11180116.jpg

th_2011-11-11180139.jpg

Na boy Collaborator

Na boy

Posted
  • Author
Posted

Thanks very much but i fear if i start with the r34 uprights then i may need to change more then i would if i went r32/33. Do you have any info on this ?

And can you tell me the bore on the marster plez

Thanks

N-DAWG Mentor

N-DAWG

Posted
Posted

Not sure the bore, but it's a BM44 part no. I believe it's the same between R34 25GT and GTT and also R33 (correct me if I'm wrong there) It seems to be quite common from my experience.

As far as I'm aware you would need matching Brake Calipers (bolt hole size) and correct size rotors, and the rest should be a bolt on job. Maybe brake lines? I got a front/rear set of ADR Approved Braided lines from Brakewest in Vic, was not much more than $200 iirc... They're street legal and better than experimenting with second hand rubber lines, and if you give him the measurements and caliper fittings he can custom make them which is what I had done.

Check in the Suspension/Braking/Handling Forum as I'm sure someone would have done same convesion/upgrade before.

This is of course presuming you're going to upgrade the brakes also. I would hardly recommend doing a 5 stud Upgrade on an R32 GTS purely for 5 stud wheel options alone...

I had my brakes upgraded from 5 Stud N/A Brakes to R33 GTSt items previous to a motor swap which is why I haven't used these to uprade my existing front brake set up.

N-DAWG Mentor

N-DAWG

Posted
Posted

Everything you see above $200 Plus Postage

Master Cylinder and Boost

Hand Break

Lines

5 stud hubs as pictured

Your choice whether you want the discs. I can measure the thickness on them to see if they've got much left or even legal thickness, but they might not be worth the cost to freight due to weight and you'll probably want a fresh pair.

I can package them up as best I can, though they are quite heavy. I know cause I had bought a pair previously from a member on here freighting them from Adelaide to Coopers Plains.

For $220 Plus Postage I can throw in a pair of Bendix Ultimate Pads to suit. I used them for a couple of months before switching to a more streetable compound so they have PLENTY of meat on them. Can send photos too if you like.

N-DAWG Mentor

N-DAWG

Posted
Posted

No worries will await your response.

I can do the master/booster combo $70 inclusive of postage on its own. Obviously if you want to arrange courier for the 5 stud hubs and the rest then the price is as above all together.

PM me when you know which way you want to go with it :)

Cheers

Nathan

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Trilbyte
      RB25 S2 Idles but doesn't want to rev

      By Trilbyte · Posted

      Update for the sake of closure   Ended up getting the intercooler piping all sorted, new plugs and yellow jacket coils, and she was idling mint until it warmed up while I was bleeding the cooling system. Found the misfire to be localised to cyl 3 by unplugging coilpacks, ran a compression test, that checked out, then decided to get a mate to check if that spark plug was firing out of the motor. Upon cranking it over, with the injectors disconnected, the car actually fired and ran on a couple cylinders and heaps of fuel came out the top of cyl 3 I'd say that injector's either spraying incorrectly or spraying far too much, which is fine as I'm planning on replacing them anyway I'm planning on making about 250kW on flex fuel, and have a set of 1000cc injectors from ozautosport, obviously overkill but I'm planning on building the motor and running more boost further down the line, do you reckon they'd be too big for a smooth idle on 98? Thanks for the replies gents, much appreciated
    • Dose Pipe Sutututu
      Any feedback on GReddy Turbine Kit T620Z in r33 GTST/RB25DET?

      By Dose Pipe Sutututu · Posted

      Nice modern Hypergear high flow would be perfect.
    • Murray_Calavera
      Steps to DIY sanding car back ready for respray....

      By Murray_Calavera · Posted

      I'm confused. You said you want to "remove the clear coat from most panels" but it sounds like you are actually doing a full respray? Few random things to add -  If you chase the blistered paint with 120 grit, I can almost guarantee you'll chase it down to bare metal (that's fine). But if you paint the car from here, you'll have nice little indents where ever the blistered paint was. The new paint won't magically level out the low areas, you need to fill them. Which leads me to the main point I wanted to add, make sure the whole car is flat before you paint it. All those areas with blistered paint you sanded out, make sure to fill them and triple check they are flat with a block guide coat. I'd also check the whole car is flat with a large block and guide coat but yeah up to you if you want to go that far.   
    • Duncan
      Any feedback on GReddy Turbine Kit T620Z in r33 GTST/RB25DET?

      By Duncan · Posted

      300hp (225kw) is barely outside the standard turbo's range with a bit of extra boost in it (200ish). If you are going to change the turbo you should aim for 250-300kw (330-400hp) to make the expense worthwhile
    • Murray_Calavera
      Any feedback on GReddy Turbine Kit T620Z in r33 GTST/RB25DET?

      By Murray_Calavera · Posted

      A couple of things, firstly omg that turbo is expensive! $3,000 USD for dinosaur technology is robbery. You could buy a G series turbo and have a good amount of change instead.  If you want a good budget option, have a look here - https://hypergearturbos.com/product/rb25dethighflow/ If you are keen to spend more, have look at the modern turbos, Garrett G series, Borgwarner EFR, etc. Have a look at the RB25 dyno results thread for inspiration.  If you upgrade your turbo to something that will support the 300hp you want and only "probably" have Haltech ECU, your car will only "probably" run. Actually, no it won't run. You are going to need the ECU and injectors at the time you do the turbo upgrade.  No thoughts on "this much boost" as you didn't say how much boost that actually is. Having said that, plenty of unopened RB25's making even more power then what you are chasing.   
×
×
  • Create New...