Jump to content
SAU Community

Recommended Posts

Hey all My car has just given up on life today and I really need some help to hopefully get close to the cause of it...

I drove it yesterday and it was fine.

I drove it for 15 mins to the mall today and it spewed its guts out in the car park... Its Brown murky water that was coming out from the rear of the engine inlet side, (My coolant was pretty green last time I checked about a week or so ago)

I proceeded to head home hoping it wouldn't overheat much as I live fairly close, but within 5 mins it got up to 110 deg

I quickly pulled into BP and it was sizzling and steaming HEAPS where all the heater hoses are under the inlet manifold next to the block. I then opened the radiator.... Empty... Filled it up with cold water.

Temp gauge said 40 deg...so I started on my way home. 1 minute down the road the temp gauge went up to 110 deg, so I pulled over again. Same thing, sizzling and steaming under the manifold.

But this is the catch, the radiator was still really cold, the top hose was hot, and the bottom hose was cold....

Im hoping its a heater hose seal broken under the pressure and leaking out there, rather than the head gasket, and im guessing my thermostat is stuffed??

Does anyone have any suggestions for the cause?

Also I live in Glen Iris, Melbourne, does anyone know and good skyline mechanics sort of near me.. I know RacePace is really good and Chris is pretty onto it, but Bays water is way to far in this situation...

Thanks guys :)

Link to comment
https://www.sau.com.au/forums/topic/400603-need-some-help-and-suggestions/
Share on other sites

one hose will always be hotter than the other as one hose is have cooled coolant flow through it and one has coolant fresh out of the engine. and given that there is a leak in the system, that will make the problem worse. also if your radiator is somewhat blocked (not totally blocked, but not flowing like a new one, which is a common problem on older cars) then that will make the radiator feel colder than it should

another possible issue is that your water pump is worn out

Water pump was also another possibility that just came to mind also, so maybe that needs looking at, I wish there was a way to test it. Its just weird because the temps rarely go above 76 deg on ecu and its always run fine, then it just did this out of the blue. Water pumps dont just work 1 day and not the next do they?

When I mention the hose and radiator were cold, I mean like chilled cold.. definitely not normal.

Thanks for the reply

i think the first thing is to get the leak sorted and then see what temps do. a leak in the cooling system will cause temps to skyrocket. for example, i've seen plenty of overheating issues caused simply by a dodgy radiator cap.

Yep. Fill up cooling system with water and pressure test, check for leaks. If no leaks are present and it holds pressure then remove thermostat and check opening temp. Replace if necessary.

Retry bleeding cooling system and try again

Today I disconnected the radiator and hoses and flushed it and the block out with heaps of water. Fitted a new thermostat. then filled it all up again.

It bubbled a little but it didn't look anything out of the ordinary. at about 90 deg it started to overflow as it would. so I put the cap on and went for a quick drive around my apartment

It didn't overheat once pressurised on the drive, It got to 90-92 deg (using water) Once home I noticed a constant dribble coming down the gearbox from above the starter motor. I cant see the actual place it was leaking from tho.

Good news is the water pump still works and it was clean water leaking not oily water as suspected earlier, nor was the radiator bubbling or dipstick with any residue. bad news is I cannot see the leak so the manifold will need to come off, Im suspecting a heater hose.

It looks like a bit of a mish to get it off and I don't have too many tools here to even consider the task ahead. Is there anyone recommended for skyline work? I dont want to take it to just any mechanic.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Good morning all, Bit of a random question but figured I’d finally throw it out after wondering for a long while. Before I start, I'm hoping to do this purely out of personal preference. I think it would look better at night, and don't mind at all spending a few hours and dollars to get it done. I've copied this from a non-Skyline specific forum, so I apologize for the explanation of our headlight switch setup that we all know. Here we go: Zero lights (switch off) Parking lights (switch position 1) being a rectangular marker on the outside of the housing, my low beam being the projector in the centre (position 2), and a high beam triggered by my turn signal stalk. Most North American cars I’ve owned of this era have power to the amber corner (turning indicator) light as part of the first switch (parking lights). I’d love to have these amber corners receive power when the headlights and parking lights are on (headlight switch), yet still blink when using the turn signal which is of course a separate switch. Hopefully I’ve explained my question correctly. Is anyone aware of a way in which I might be able to achieve this? Thanks in advance
    • My heads are cathedral port! It's likely possible, but I don't want to add any extra moving parts (I know they don't move) between the heads, manifolds, etc. It will also affect how injectors/fuel rails etc sit and I don't really know if it would change how the FAST manifold goes/sits/fits. I have the LS6 steam pipes already as I have a very late LS1 block so it should be fine. I couldn't find anyone who had ever actually used one for this purpose, it seems 100% of people grind the water pump. The thermal spacers are 12mm and are half way to the cost of the newer water pump anyhow... so if it comes to that I suppose I'd rather buy a new pump. The bearing in the pump I do have is a little.. clunky, but it hasn't done that much time and I never noticed it when the car was together in the past few years, so..
    • The bushing has failed, not all that uncommon for a car of this age.  Any mechanic should be able to push in a new bushing for you, or you can probably buy the entire lower control arm, complete with bushes.
    • Could you not use "thermal" spacers to give the clearance, like the ones I used between the blower and head? That raised the manifold height by around 10-15mm Albeit the ones I used were for cathedral ports, but I assume they have similar for rectangular ports????
    • Thanks Paul I reached out to Autotainment but they no longer work on JDM cars as the guy who used to do the work moved on and is no longer doing that kind of work. I am talking with Level Up Audio though.
×
×
  • Create New...