Jump to content
SAU Community

Recommended Posts

Hey guys need a expert advise about turbo upgrade my gf got me this off eBay which is not refundable was wondering if its worth putting in my car as it cost less then a grand … pls any advise is welcomed http://www.ebay.com/itm/SKYLINE-RB25-RB25DET-R34-R33-GT3582R-UPGRADE-turbo-kit-/330667707951?pt=Race_Car_Parts&hash=iteam4cfd54ce2f&vxp=mtr

Link to comment
https://www.sau.com.au/forums/topic/400738-r34-turbo-upgrade/
Share on other sites

Better start searching mate. Go to the rb25 dyno thread,

And send your gf back to the kitchen. This would never have happened if she didn't leave the kitchen.

:rofl2:

If it was my car i know i wouldnt be fitting it up, it will be laggy but thats the least of your problems... Getting piping etc made to suit, re-tuned and all that stuff just to SEE if the chinese POS works? I would Ebay it and let some other goose give it a go... BUT thats just me :wave:

No such thing if you want to do it properly. Even less likely for an R34GTT... If you want to do a cost effective turbo upgrade then i would suggest the HG turbos... Any way you go with a turbo upgrade is going to cost decent money!

You should be fine, go have a read of the HG thread along with a squizz at the RB25 dyno section etc....

My car was running 200kw when i got it with high flow turbo, Power FC, Standard AFM, Standard Injectors etc.... I upgraded the injectors to 550cc and ran 250kw still running the standard AFM (However i would suggest you upgrade it if you are going for a retune anyway), make sure your fuel pump is up to the task and ideally have exhaust, cooler and some form of boost control.... There are many ways around making power but simple ways are very effective!

I'd keep it subtle but responsive for a street tune.

Upgrade to a R34 GTR N1 turbo (Ball Bearing Steel Internals).

Which is equivalent to a Garrett -7 or more so very similar.

For a bit more top end go for a Garrett -9.

I'd keep it subtle but responsive for a street tune.

Upgrade to a R34 GTR N1 turbo (Ball Bearing Steel Internals).

Which is equivalent to a Garrett -7 or more so very similar.

For a bit more top end go for a Garrett -9.

GTT dude... Not GTR?

haha thought so!

Best off keeping it simple..... My original highflow was all factory bolt up, so for stealth and cost reasons he should aim for somthing like that.... Other GTT's out there making good power with them, mine didnt as the tuner was a retard.... Since then i got bored and continued on to a high mount, but the cost outweighs the cost of the car so when you see a post "Not very expensive"you generally steer away from MOST aftermarket setups :P

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • f**kin' yikes! That insulation is the shittest stuff I have ever seen. You need to do an insurance job on that f**ker, pronto. WRT to the washer cover, I would have said that there'd have to be some at a wrecker, then remembered that it's a BMW, and reasoned that every single wrecked one would have been tailgating and so the front end would be trashed.
    • Oh and I lost my headlight washer jet cover!
    • Ok, so I got myself some X1 wheels really cheap to try out, they're a bit different and I like them but they're really narrow (18x8) they are available in staggered 18x8/9 also but really hard to find.  I kinda dig them, but not as much as the F10 19's I usually run, so these go into the wheel pile.         As I mentioned in another thread, I got a new exhaust. It's an off-the-shelf stainless one that fits OH-KAY. I don't love the tips size and how far they come out the back, I think I might cut the tips off and replace with some smaller (~3") ones that don't extend as far. It sounds really good though, I'm not sure if its just in my head but the car feels a little quicker, more responsive.      I fitted an eBay special front lip. Surprisingly it fit perfectly and all holes lined up. Its a little rickety but I haven't put any double sided tape on yet, I want to clean the front bar up where it has scraped the road a lot and fil in the number plate holes (or, get body coloured wrap to cover them - is this a thing?  I'm not sure if I'll leave it gloss or pain it matte. I really like it though, I don't particularly like the front bar without it, I don't really like the M-Sport and to get anything else is just too expensive. That said, I might need a new one now anyway as I dropped the car onto the jack after forgetting to put ramps under the front wheels. It bent a lot and while it did go back to normal after I got the car off the jack, I do fear I have not done it any favours.    Lastly, my headlights died. Different problems in each. They have gotten much dimmer over the past year or so, I put new (uber expensive) OSRAM bulbs in them but to no avail. One of them pointed at the ground and the other just kinda did its own thing with light working sometimes. Yeah, check this 18 year old BMW headlight wire. I reckon I know why they were stuffed.            BTW, the yellow and black is the power to the Xenons. Yikes. I hunted around an researched my options here. I would have loved to just get a replacement harness but not a thing. My car has adaptive headlights, that is they rotate left and right with the steering wheel. Good condition used adaptive xenons were over $700 each, non adaptive were around $400 each, but I couldn't help but think that they're all around 18 years old now, surely they'd have the same problems. So I looked at newer LCI headlights but they were even more expensive and I couldn't confirm that they'd be plug and play with lots of people having lots of opinions so not worth the risk.  I ended up getting brand new Chinese headlights from MARS. They're very close to OEM with only the angel eyes being a bit different. I didnt want crazy turn signals or sharp DRL's or anything. Not my bag.  They're not adaptive, I thought thats a feature I wouldn't really miss. So I coded that out.  The lights are awesome, they look so nice and they take so many years off the car. The angel eyes look great and the headlight brightness is ridiculous. I was so used to the old ones, I didn't realise just how bad they were. The new ones use the OEM bulbs, Xenon ballast and leveller motor which I was happier with. The only issue with them is that the rear cover is held on by SEVEN screws. This will be a nightmare to get to and open when I need to change bulbs.   
    • Now that you mention it I can see those too. More subtle. The lighting and low resolution makes it hard to assess super well what's going on but what is visible is bad enough to pull the motor.
    • I feel like this is due an update
×
×
  • Create New...